View AK4645EZ_4112415.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

[AK4645EZ]
AK4645EZ
Stereo CODEC with MIC/HP-AMP
GENERAL DESCRIPTION The AK4645 is a stereo CODEC with a built-in Microphone-Amplifier and Headphone-Amplifier. The AK4645 features analog mixing circuits and PLL that allows easy interfacing in mobile phone and portable A/V player designs. The AK4645 is available in a 32pin QFN (4mm x 4mm), utilizing less board space than competitive offerings. FEATURES 1. Recording Function * 4 Stereo Input Selector * Stereo Mic Input (Full-differential or Single-ended) * Stereo Line Input * MIC Amplifier (+32dB/+26dB/+20dB or 0dB) * Digital ALC (Automatic Level Control) (+36dB -54dB, 0.375dB Step, Mute) * ADC Performance: S/(N+D): 83dB, DR, S/N: 86dB (MIC-Amp=+20dB) S/(N+D): 88dB, DR, S/N: 95dB (MIC-Amp=0dB) * Wind-noise Reduction Filter * Stereo Separation Emphasis * Programmable EQ 2. Playback Function * Digital De-emphasis Filter (tc=50/15(s, fs=32kHz, 44.1kHz, 48kHz) * Bass Boost * Soft Mute * Digital Volume (+12dB ( (115.0dB, 0.5dB Step, Mute) * Digital ALC (Automatic Level Control) (+36dB -54dB, 0.375dB Step, Mute) * Stereo Separation Emphasis * Programmable EQ * Stereo Line Output - Performance: S/(N+D): 88dB, S/N: 92dB * Stereo Headphone-Amp - S/(N+D): 70dB@7.5mW, S/N: 90dB - Output Power: 70mW@16 (HVDD=5V), 62mW@16 (HVDD=3.3V) - Pop Noise Free at Power ON/OFF * Analog Mixing: 4 Stereo Input 3. Power Management 4. Master Clock: (1) PLL Mode * Frequencies: - MCKI pin: 11.2896MHz, 12MHz, 12.288MHz, 13MHz, 13.5MHz, 19.2MHz, 24MHz, 26MHz, 27MHz - LRCK pin: 1fs - BICK pin: 32fs or 64fs (2) External Clock Mode * Frequencies: 256fs, 512fs or 1024fs (MCKI pin) 5. Output Master Clock Frequencies: 32fs/64fs/128fs/256fs 6. Sampling Rate: * PLL Slave Mode (LRCK pin): 7.35kHz 48kHz * PLL Slave Mode (BICK pin): 7.35kHz 48kHz * PLL Slave Mode (MCKI pin): 8kHz, 11.025kHz, 12kHz, 16kHz, 22.05kHz, 24kHz, 32kHz, 44.1kHz, 48kHz
MS0605-E-00 -12007/06
[AK4645EZ]
* PLL Master Mode: 8kHz, 11.025kHz, 12kHz, 16kHz, 22.05kHz, 24kHz, 32kHz, 44.1kHz, 48kHz * EXT Master/Slave Mode: 7.35kHz 48kHz (256fs), 7.35kHz 26kHz (512fs), 7.35kHz 13kHz (1024fs) 7. P I/F: 3-wire serial, I2C Bus (Ver 1.0, 400kHz Fast-mode) 8. Master/Slave mode 9. Audio Interface Format: MSB First, 2's complement * ADC: 16bit MSB justified, I2S, DSP Mode * DAC: 16bit MSB justified, 16bit LSB justified, 16-24bit I2S, DSP Mode 10. Ta = -30 85C 11. Power Supply: * AVDD, DVDD: 2.6 3.6V (typ. 3.3V) * HVDD: 2.6 5.25V (typ. 3.3V/5.0V) * TVDD (Digital I/O): 1.6 3.6V (typ. 3.3V) 12. Package: 32pin QFN (4mm x 4mm, 0.4mm pitch) 13. Register Compatible with AK4644
Block Diagram
AVDD
PMMP
AVSS
VCOM
DVDD
TVDD
MPWR
MIC Power Supply
PMADL or PMMICL
I2C Control Register CSN/CAD0 CCLK/SCL CDTI/SDA
LIN1/IN1- Internal MIC
RIN1/IN1+ MIC-Amp
PMADR or PMMICR
PMADL or PMADR
PDN
A/D
HPF
LIN2/IN2+ External MIC
Wind-Noise Stereo ALC Reduction Separation
RIN2/IN2-
BICK LRCK SDTO
MIN/LIN3 Line In * RIN3 LIN4/IN4+
PMAINR2 PMAINL2
Audio I/F
SDTI
PMAINR3
Line In
RIN4/IN4-
PMAINR4 PMAINL4 PMLO PMAINL3 PMMIN PMDAC
LOUT/LOP Stereo Line Out D/A ROUT/LON
PMPLL PMHPL
Stereo DATT Bass ALC Separation SMUTE Boost
HPF
MCKO PLL MCKI * VCOC
HPL Headphone HPR MUTET
PMHPR
HVDD
HVSS
(VCOC and RIN3 pins are shared by the same pin.) Figure 1. Block Diagram
MS0605-E-00 -2-
2007/06
[AK4645EZ]
Ordering Guide
AK4645EZ AKD4645 -30 +85C 32pin QFN (0.4mm pitch) Evaluation board for AK4645
Pin Layout
RIN4 / IN4-
MUTET
MCKO 18
HVDD
HVSS
24
23
22
21
20
LIN4 / IN4+ ROUT / LON LOUT / LOP MIN / LIN3 RIN2 / IN2- LIN2 / IN2+ LIN1 / IN1- RIN1 / IN1+
19
17
MCKI
HPR
HPL
25 26 27 28 29 30 31 32 1 2 3 4 5 6 7 8
16 15 14
TVDD DVDD BICK LRCK SDTO SDTI CDTI / SDA CCLK / SCL
AK4645EZ
Top View
13 12 11 10 9
MPWR
VCOM
AVDD
VCOC / RIN3
AVSS
Compatibility with AK4643/44
1. Function Function Digital I/O of P I/F Analog Mixing for Playback Input Selector for Recording HP-Amp Hi-Z Setting for wired OR PLL Speaker-Amp Receiver-Amp Package AK4643 2.6 to 3.6V 3 Stereo 3 Stereo No 11.2896/12/12.288/ 13.5/24/27MHz Yes Yes 32QFN (5mm x 5mm, 0.5mm pitch) AK4644 AK4645EZ 1.6 to 3.6V 4 Stereo 4 Stereo Yes 11.2896/12/12.288/13/ 13.5/19.2/24/26/27MHz No 32QFN (4mm x 4mm, 0.4mm pitch)
No
MS0605-E-00 -3-
CSN / CAD0
PDN
I2C
2007/06
[AK4645EZ]
2. Pin Pin# 16 19 20 21 22 23 24 25 26 27 AK4643 DVSS SPN SPP HVDD HVSS HPR HPL MUTET ROUT/RCN LOUT/RCP AK4644 TEST1 TEST2 AK4645EZ TVDD HVSS HVDD HPR HPL MUTET RIN4 / IN4- LIN4 / IN4+ ROUT/LON LOUT/LOP
3. Register (difference from AK4644)
Addr 00H 01H 02H 03H 04H 05H 06H 07H 08H 09H 0AH 0BH 0CH 0DH 0EH 0FH 10H 11H 12H 13H 14H 15H 16H 17H 18H 19H 1AH 1BH 1CH 1DH 1EH 1FH 20H 21H 22H 23H 24H Register Name Power Management 1 Power Management 2 Signal Select 1 Signal Select 2 Mode Control 1 Mode Control 2 Timer Select ALC Mode Control 1 ALC Mode Control 2 Lch Input Volume Control Lch Digital Volume Control ALC Mode Control 3 Rch Input Volume Control Rch Digital Volume Control Mode Control 3 Mode Control 4 Power Management 3 Digital Filter Select FIL3 Co-efficient 0 FIL3 Co-efficient 1 FIL3 Co-efficient 2 FIL3 Co-efficient 3 EQ Co-efficient 0 EQ Co-efficient 1 EQ Co-efficient 2 EQ Co-efficient 3 EQ Co-efficient 4 EQ Co-efficient 5 FIL1 Co-efficient 0 FIL1 Co-efficient 1 FIL1 Co-efficient 2 FIL1 Co-efficient 3 Power Management 4 Mode Control 5 Lineout Mixing Select HP Mixing Select Reserved D7 0 HPZ 0 LOVL PLL3 PS1 DVTM 0 REF7 IVL7 DVL7 RGAIN1 IVR7 DVR7 0 0 INR1 GN1 F3A7 F3AS F3B7 0 EQA7 EQA15 EQB7 0 EQC7 EQC15 F1A7 F1AS F1B7 0
PMAINR4
D6
PMVCM
HPMTN 0 LOPS PLL2 PS0 WTM2 0 REF6 IVL6 DVL6 LMTH1 IVR6 DVR6 LOOP 0 INL1 GN0 F3A6 0 F3B6 0 EQA6 EQA14 EQB6 0 EQC6 EQC14 F1A6 0 F1B6 0
PMAINL4
D5 PMMIN PMHPL 0
MGAIN1
PLL1 FS3 ZTM1 ALC REF5 IVL5 DVL5 0 IVR5 DVR5 SMUTE 0 HPG 0 F3A5 F3A13 F3B5 F3B13 EQA5 EQA13 EQB5 EQB13 EQC5 EQC13 F1A5 F1A13 F1B5 F1B13
PMAINR3
D4 0 PMHPR DACL 0 PLL0 MSBS ZTM0 ZELMN REF4 IVL4 DVL4 0 IVR4 DVR4 DVOLC 0 MDIF2 FIL1 F3A4 F3A12 F3B4 F3B12 EQA4 EQA12 EQB4 EQB12 EQC4 EQC12 F1A4 F1A12 F1B4 F1B12
PMAINL3
D3 PMLO M/S 0 0 BCKO BCKP WTM1 LMAT1 REF3 IVL3 DVL3 0 IVR3 DVR3 BST1 IVOLC MDIF1 EQ F3A3 F3A11 F3B3 F3B11 EQA3 EQA11 EQB3 EQB11 EQC3 EQC11 F1A3 F1A11 F1B3 F1B11
PMAINR2
D2 PMDAC 0 PMMP MINL 0 FS2 WTM0 LMAT0 REF2 IVL2 DVL2 0 IVR2 DVR2 BST0 HPM INR0 FIL3 F3A2 F3A10 F3B2 F3B10 EQA2 EQA10 EQB2 EQB10 EQC2 EQC10 F1A2 F1A10 F1B2 F1B10
PMAINL2
D1 0 MCKO 0 0 DIF1 FS1 RFST1 RGAIN0 REF1 IVL1 DVL1 VBAT IVR1 DVR1 DEM1 MINH INL0 0 F3A1 F3A9 F3B1 F3B9 EQA1 EQA9 EQB1 EQB9 EQC1 EQC9 F1A1 F1A9 F1B1 F1B9
PMMICR
D0 PMADL PMPLL
MGAIN0
0 DIF0 FS0 RFST0 LMTH0 REF0 IVL0 DVL0 0 IVR0 DVR0 DEM0 DACH PMADR 0 F3A0 F3A8 F3B0 F3B8 EQA0 EQA8 EQB0 EQB8 EQC0 EQC8 F1A0 F1A8 F1B0 F1B8
PMMICL
0 LOM 0 0
0 MICR3 MICL3 L4DIF LOM3 RINR4 LINL4 RINR3 HPM3 RINH4 LINH4 RINH3 0 0 0 0 These bits are added in the AK4645.
MIX LINL3 LINH3 0
AIN3 RINR2 RINH2 0
LODIF
LINL2 LINH2 0
MS0605-E-00 -4-
2007/06
[AK4645EZ]
PIN/FUNCTION
Function MIC Power Supply Pin Common Voltage Output Pin, 0.45 x AVDD 2 VCOM O Bias voltage of ADC inputs and DAC outputs. 3 AVSS Analog Ground Pin 4 AVDD Analog Power Supply Pin, 2.6 3.6V Output Pin for Loop Filter of PLL Circuit (AIN3 bit = "0": PLL is available.) VCOC O 5 This pin should be connected to AVSS with one resistor and capacitor in series. RIN3 I Rch Analog Input 3 Pin (AIN3 bit = "1": PLL is not available.) Control Mode Select Pin 6 I2C I "H": I2C Bus, "L": 3-wire Serial Power-Down Mode Pin 7 PDN I "H": Power-up, "L": Power-down, reset and initializes the control register. CSN I Chip Select Pin (I2C pin = "L": 3-wire Serial Mode) 8 CAD0 I Chip Address 1 Select Pin (I2C pin = "H": I2C Bus Mode) CCLK I Control Data Clock Pin (I2C pin = "L": 3-wire Serial Mode) 9 SCL I Control Data Clock Pin (I2C pin = "H": I2C Bus Mode) CDTI I Control Data Input Pin (I2C pin = "L": 3-wire Serial Mode) 10 SDA I/O Control Data Input Pin (I2C pin = "H": I2C Bus Mode) 11 SDTI I Audio Serial Data Input Pin 12 SDTO O Audio Serial Data Output Pin 13 LRCK I/O Input / Output Channel Clock Pin 14 BICK I/O Audio Serial Data Clock Pin 15 DVDD Digital Power Supply Pin, 2.6 3.6V 16 TVDD Digital I/O Power Supply Pin, 1.6 3.6V 17 MCKI I External Master Clock Input Pin 18 MCKO O Master Clock Output Pin 19 HVSS Headphone Amp Ground Pin 20 HVDD Headphone Amp Power Supply Pin 21 HPR O Rch Headphone-Amp Output Pin 22 HPL O Lch Headphone-Amp Output Pin Mute Time Constant Control Pin 23 MUTET O Connected to HVSS pin with a capacitor for mute time constant. RIN4 I Rch Analog Input 4 Pin (L4DIF bit = "0": Single-ended Input) 24 IN4- I Negative Line Input 4 Pin (L4DIF bit = "1": Full-differential Input) LIN4 I Lch Analog Input 4 Pin (L4DIF bit = "0": Single-ended Input) 25 IN4+ I Positive Line Input 4 Pin (L4DIF bit = "1": Full-differential Input) ROUT O Rch Stereo Line Output Pin (LODIF bit = "0": Single-ended Stereo Output) 26 LON O Negative Line Output Pin (LODIF bit = "1": Full-differential Mono Output) LOUT O Lch Stereo Line Output Pin (LODIF bit = "0": Single-ended Stereo Output) 27 LOP O Positive Line Output Pin (LODIF bit = "1": Full-differential Mono Output) MIN I Mono Signal Input Pin (AIN3 bit = "0": PLL is available.) 28 LIN3 I Lch Analog Input 3 Pin (AIN3 bit = "1": PLL is not available.) RIN2 I Rch Analog Input 2 Pin (MDIF2 bit = "0": Single-ended Input) 29 IN2- I Microphone Negative Input 2 Pin (MDIF2 bit = "1": Full-differential Input) LIN2 I Lch Analog Input 2 Pin (MDIF2 bit = "0": Single-ended Input) 30 IN2+ I Microphone Positive Input 2 Pin (MDIF2 bit = "1": Full-differential Input) LIN1 I Lch Analog Input 1 Pin (MDIF1 bit = "0": Single-ended Input) 31 IN1- I Microphone Negative Input 1 Pin (MDIF1 bit = "1": Full-differential Input) RIN1 I Rch Analog Input 1 Pin (MDIF1 bit = "0": Single-ended Input) 32 IN1+ I Microphone Positive Input 1 Pin (MDIF1 bit = "1": Full-differential Input) Note 1. All input pins except analog input pins (MIN/LIN3, LIN1, RIN1, LIN2, RIN2, RIN3, RIN4, LIN4) should not be left floating. Note 2. AVDD or AVSS voltage should be input to I2C pin. No. 1 Pin Name MPWR I/O O
MS0605-E-00 -5-
2007/06
[AK4645EZ]
Handling of Unused Pin
The unused I/O pins should be processed appropriately as below. Classification Analog Pin Name MPWR, VCOC/RIN3, HPR, HPL, MUTET, RIN4/IN4-, LIN4/IN4+, ROUT/LOP, LOUT/LON, MIN/LIN3, RIN2/IN2-, LIN2/IN2+, LIN1/IN1-, RIN1/IN1+ MCKO MCKI Setting These pins should be open. This pin should be open. This pin should be connected to HVSS.
Digital
ABSOLUTE MAXIMUM RATINGS (AVSS, HVSS=0V; Note 3, Note 4) Parameter Symbol min Power Supplies: Analog AVDD -0.3 Digital DVDD -0.3 Digital I/O TVDD -0.3 Headphone-Amp HVDD -0.3 Input Current, Any Pin Except Supplies IIN Analog Input Voltage (Note 5) VINA -0.3 Digital Input Voltage (Note 6) VIND -0.3 Ambient Temperature (powered applied) Ta -30 Storage Temperature Tstg -65
max 6.0 6.0 6.0 6.0 10 AVDD+0.3 TVDD+0.3 85 150
Units V V V V mA V V C C
Note 3. All voltages with respect to ground. Note 4. AVSS and HVSS must be connected to the same analog ground plane. Note 5. I2C, RIN4/IN4-, LIN4/IN4+, MIN/LIN3, RIN3, RIN2/IN2-, LIN2/IN2+, LIN1/IN1-, RIN1/IN1+ pins Note 6. PDN, CSN/CAD0, CCLK/SCL, CDTI/SDA, SDTI, LRCK, BICK, MCKI pins Pull-up resistors at SDA and SCL pins should be connected to (TVDD+0.3)V or less voltage. WARNING: Operation at or beyond these limits may result in permanent damage to the device. Normal operation is not guaranteed at these extremes.
RECOMMENDED OPERATING CONDITIONS
(AVSS, HVSS=0V; Note 3) Parameter Power Supplies Analog (Note 7) Digital Digital I/O HP-Amp Difference Symbol AVDD DVDD TVDD HVDD AVDD-DVDD min 2.6 2.6 1.6 2.6 -0.3 typ 3.3 3.3 3.3 3.3 / 5.0 0 max 3.6 3.6 DVDD 5.25 +0.3 Units V V V V V
Note 3. All voltages with respect to ground. Note 7. The power-up sequence between AVDD, DVDD, TVDD and HVDD is not critical. PDN pin should be held to "L" upon power-up. PDN pin should be set to "H" after all power supplies are powered-up. The AK4645 should be operated by the recommended power-up/down sequence shown in "System Design (Grounding and Power Supply Decoupling)" to avoid the pop noise at line output and headphone output. When one of power supplies is partially powered OFF, the power supply current at power-down mode may be increased. All the power supplies should be powered OFF when the power supply is powered OFF. * AKEMD assumes no responsibility for the usage beyond the conditions in this datasheet.
MS0605-E-00 -6-
2007/06
[AK4645EZ]
ANALOG CHARACTERISTICS (Ta=25C; AVDD, DVDD, TVDD, HVDD=3.3V; AVSS=HVSS=0V; fs=44.1kHz, BICK=64fs; Signal Frequency=1kHz; 16bit Data; Measurement frequency=20Hz 20kHz; unless otherwise specified) min typ max Units Parameter MIC Amplifier: LIN1/RIN1/LIN2/RIN2/LIN4/RIN4 pins & LIN3/RIN3 pins (AIN3 bit = "1"); MDIF1=MDIF2 bits = "0" (Single-ended inputs) Input MGAIN1-0 bits = "00" 40 60 80 k Resistance MGAIN1-0 bits = "01", "10"or "11" 20 30 40 k MGAIN1-0 bits = "00" 0 dB MGAIN1-0 bits = "01" +20 dB Gain MGAIN1-0 bits = "10" +26 dB MGAIN1-0 bits = "11" +32 dB MIC Amplifier: IN1+/IN1-/IN2+/IN2- pins; MDIF1 = MDIF2 bits = "1" (Full-differential input) Maximum Input Voltage (Note 8) MGAIN1-0 bits = "01" 0.228 Vpp MGAIN1-0 bits = "10" 0.114 Vpp MGAIN1-0 bits = "11" 0.057 Vpp MIC Power Supply: MPWR pin Output Voltage (Note 9) 2.22 2.47 2.72 V Load Resistance 0.5 k Load Capacitance 30 pF ADC Analog Input Characteristics: LIN1/RIN1/LIN2/RIN2/LIN4/RIN4 pins & LIN3/RIN3 pins (AIN3 bit = "1") ADC IVOL, IVOL=0dB, ALC=OFF Resolution 16 Bits (Note 11) 0.168 0.198 0.228 Vpp Input Voltage (Note 10) 1.68 1.98 2.28 Vpp (Note 12) (Note 11, LIN1/RIN1/LIN2/RIN2) 71 83 dBFS S/(N+D) (Note 11, LIN3/RIN3/LIN4/RIN4) 83 dBFS (-1dBFS) (Note 12, except for LIN3/RIN3) 88 dBFS (Note 12, LIN3/RIN3) 72 dBFS (Note 11) 76 86 dB D-Range (-60dBFS, A-weighted) 95 dB (Note 12) (Note 11) 76 86 dB S/N (A-weighted) 95 dB (Note 12) (Note 11) 75 90 dB Interchannel Isolation 100 dB (Note 12) (Note 11) 0.1 0.8 dB Interchannel Gain Mismatch 0.1 0.8 dB (Note 12)
Note 8. The voltage difference between IN1/2+ and IN1/2- pins. AC coupling capacitor should be inserted in series at each input pin. Full-differential mic input is not available at MGAIN1-0 bits = "00". Maximum input voltage of IN1+, IN1-, IN2+ and IN2- pins are proportional to AVDD voltage, respectively. Vin = 0.069 x AVDD (max)@MGAIN1-0 bits = "01", 0.035 x AVDD (max)@MGAIN1-0 bits = "10", 0.017 x AVDD (max)@MGAIN1-0 bits = "11". When the signal larger than above value is input to IN1+, IN1-, IN2+ or IN2- pin, ADC does not operate normally. Note 9. Output voltage is proportional to AVDD voltage. Vout = 0.75 x AVDD (typ) Note 10. Input voltage is proportional to AVDD voltage. Vin = 0.06 x AVDD (typ)@MGAIN1-0 bits = "01" (+20dB), Vin = 0.6 x AVDD(typ)@MGAIN1-0 bits = "00" (0dB) Note 11. MGAIN1-0 bits = "01" (+20dB) Note 12. MGAIN1-0 bits = "00" (0dB)
MS0605-E-00 -7-
2007/06
[AK4645EZ]
min typ max Units Parameter DAC Characteristics: Resolution 16 Bits Stereo Line Output Characteristics: DAC LOUT/ROUT pins, ALC=OFF, IVOL=0dB, DVOL=0dB, LOVL bit = "0", LODIF bit = "0", RL=10k (Single-ended); unless otherwise specified. Output Voltage (Note 13) LOVL bit = "0" 1.78 1.98 2.18 Vpp LOVL bit = "1" 2.25 2.50 2.75 Vpp 78 88 dBFS S/(N+D) (-3dBFS) S/N (A-weighted) 82 92 dB Interchannel Isolation 80 100 dB Interchannel Gain Mismatch 0.1 0.5 dB Load Resistance 10 k Load Capacitance 30 pF Mono Line Output Characteristics: DAC LOP/LON pins, ALC=OFF, IVOL=0dB, DVOL=0dB, LOVL bit = "0", LODIF bit = "1", RL=10k for each pin (Full-differential) Output Voltage (Note 14) LOVL bit = "0" 3.52 3.96 4.36 Vpp LOVL bit = "1" 5.00 Vpp 78 88 dBFS S/(N+D) (-3dBFS) S/N (A-weighted) 85 95 dB Load Resistance (LOP/LON pins, respectively) 10 k Load Capacitance (LOP/LON pins, respectively) 30 pF Note 13. Output voltage is proportional to AVDD voltage. Vout = 0.6 x AVDD (typ)@LOVL bit = "0". Note 14. Output voltage is proportional to AVDD voltage. Vout = (LOP) - (LON) = 1.2 x AVDD (typ)@LOVL bit = "0".
MS0605-E-00 -8-
2007/06
[AK4645EZ]
min typ max Units Parameter Headphone-Amp Characteristics: DAC HPL/HPR pins, ALC=OFF, IVOL=0dB, DVOL=0dB, VBAT bit = "0"; unless otherwise specified. Output Voltage (Note 15) 1.58 1.98 2.38 Vpp HPG bit = "0", 0dBFS, HVDD=3.3V, RL=22.8 2.40 3.00 3.60 Vpp HPG bit = "1", 0dBFS, HVDD=5V, RL=100 HPG bit = "1", 0dBFS, HVDD=3.3V, RL=16 (Po=62mW) 1.0 Vrms HPG bit = "1", 0dBFS, HVDD=5V, RL=16 (Po=70mW) 1.06 Vrms S/(N+D) 60 70 dBFS HPG bit = "0", -3dBFS, HVDD=3.3V, RL=22.8 80 dBFS HPG bit = "1", -3dBFS, HVDD=5V, RL=100 HPG bit = "1", 0dBFS, HVDD=3.3V, RL=16 (Po=62mW) 20 dBFS HPG bit = "1", 0dBFS, HVDD=5V, RL=16 (Po=70mW) 70 dBFS (Note 16) 80 90 dB S/N (A-weighted) 90 dB (Note 17) (Note 16) 65 75 dB Interchannel Isolation 80 dB (Note 17) (Note 16) 0.1 0.8 dB Interchannel Gain Mismatch 0.1 0.8 dB (Note 17) Load Resistance 16 C1 in Figure 2 30 pF Load Capacitance 300 pF C2 in Figure 2 Note 15. Output voltage is proportional to AVDD voltage. Vout = 0.6 x AVDD(typ)@HPG bit = "0", 0.91 x AVDD(typ)@HPG bit = "1". Note 16. HPG bit = "0", HVDD=3.3V, RL=22.8. Note 17. HPG bit = "1", HVDD=5V, RL=100.
HP-Amp
HPL/HPR pin 47F 6.8 C1 0.22F 10 C2 16 Measurement Point
Figure 2. Headphone-Amp output circuit
MS0605-E-00 -9-
2007/06
[AK4645EZ]
min typ Parameter Mono Input: MIN pin (AIN3 bit = "0"; External Input Resistance=20k) Maximum Input Voltage (Note 18) 1.98 Gain (Note 19) MIN LOUT/ROUT LOVL bit = "0" 0 -4.5 LOVL bit = "1" +2 MIN HPL/HPR HPG bit = "0" -24.5 -20 HPG bit = "1" -16.4 Stereo Input: LIN2/RIN2/LIN4/RIN4 pins; LIN3/RIN3 pins (AIN3 bit = "1") Maximum Input Voltage (Note 20) 1.98 Gain LIN/RIN LOUT/ROUT LOVL bit = "0" 0 -4.5 LOVL bit = "1" +2 LIN/RIN HPL/HPR HPG bit = "0" 0 -4.5 HPG bit = "1" +3.6 Full-differential Mono Input: IN4+/- pins (L4DIF bit = "1") Maximum Input Voltage (Note 21) 3.96 Gain LOVL bit = "0" IN4+/- LOUT/ROUT -10.5 -6 (LODIF bit = "0") LOVL bit = "1" -4 LOVL bit = "0" 0 IN4+/- LOP/LON -4.5 (LODIF bit = "1", Note 22) LOVL bit = "1" +2 HPG bit = "0" IN4+/- HPL/HPR -10.5 -6 HPG bit = "1" -2.4 Power Supplies: Power-Up (PDN pin = "H") All Circuit Power-up: AVDD+DVDD+TVDD (Note 23) 16 HVDD: HP-Amp Normal Operation 5 No Output (Note 24) Power-Down (PDN pin = "L") (Note 25) AVDD+DVDD+TVDD+HVDD 1
max +4.5 -15.5 +4.5 +4.5 -1.5 +4.5 -1.5 -
Units Vpp dB dB dB dB Vpp dB dB dB dB Vpp dB dB dB dB dB dB
24 8 100
mA mA A
Note 18. Maximum voltage is in proportion to both AVDD and external input resistance (Rin). Vin = 0.6 x AVDD x Rin / 20k (typ). Note 19. The gain is in inverse proportion to external input resistance. Note 20. Maximum Input voltage is proportional to AVDD voltage. Vout = 0.6 x AVDD (typ). Note 21. Maximum Input voltage is proportional to AVDD voltage. Vout = (IN4+) - (IN4-) = 1.2 x AVDD (typ). The signals with same amplitude and inverted phase should be input to IN4+ and IN4- pins, respectively. Note 22. Vout = (LOP) - (LON) at LODIF bit = "1". Note 23. PLL Master Mode (MCKI=12.288MHz) and PMADL = PMADR = PMDAC = PMLO = PMHPL = PMHPR = PMVCM = PMPLL = MCKO = PMMIN = PMMP = M/S bits = "1". MPWR pin outputs 0mA. AVDD=11mA(typ), DVDD=3mA(typ), TVDD=2mA(typ). EXT Slave Mode (PMPLL = M/S = MCKO bits = "0"): AVDD=10mA(typ), DVDD=3mA(typ), TVDD=0.03mA(typ). Note 24. PMADL = PMADR = PMDAC = PMLO = PMHPL = PMHPR = PMVCM = PMPLL = PMMIN bits = "1". Note 25. All digital input pins are fixed to TVDD or HVSS.
MS0605-E-00 - 10 -
2007/06
[AK4645EZ]
Power Consumption for each operation mode
Condtions: Ta=25C; AVDD=DVDD=TVDD=HVDD=3.3V; AVSS=HVSS=0V; fs=44.1kHz, External Slave Mode, BICK=64fs; 1kHz, 0dBFS input; Headphone = No output.
Power Management Bit 00H 01H 10H 20H Total Power [mW] 0 21.2 35.1 22.8 24.2 17.3 52.9
AVDD [mA]
DVDD [mA]
PMAINR2
PMAINR3
All Power-down DAC Lineout DAC HP LIN2/RIN2 HP LIN2/RIN2 ADC LIN1 (Mono) ADC LIN2/RIN2 ADC & DAC HP
0 1 1 1 1 1 1
0 0 0 0 0 0 0
0 1 0 0 0 0 0
0 1 1 0 0 0 1
0 0 0 0 1 1 1
0 0 1 1 0 0 1
0 0 1 1 0 0 1
0 0 0 0 1 0 1
0 0 0 0 0 0 0
0 0 0 0 0 0 0
0 0 0 1 0 0 0
0 0 0 1 0 0 0
0 0 0 0 0 0 0
0 0 0 0 0 0 0
0 0 0 0 0 0 0
PMAINR4
PMAINL2
PMAINL3
PMAINL4
Mode PMMICR PMMICL PMVCM PMDAC PMADR PMADL PMHPR PMMIN PMHPL PMLO
0 0 0 0 0 0 0
0 4.4 3.8 1.9 5.5 3.5 8.3
0 1.8 1.8 0 1.6 1.5 2.7
0 0.03 0.03 0 0.03 0.03 0.03
Table 1. Power Consumption for each operation mode (typ)
MS0605-E-00 - 11 -
HVDD [mA] 0 0.2 5 5 0.2 0.2 5
TVDD [mA]
2007/06
[AK4645EZ]
FILTER CHARACTERISTICS (Ta=25C; AVDD, DVDD=2.6 3.6V; TVDD=1.6 3.6V; HVDD=2.6 5.25V; fs=44.1kHz; DEM=OFF; FIL1=FIL3=EQ=OFF) Parameter Symbol min typ max Units ADC Digital Filter (Decimation LPF): Passband (Note 26) PB 0 17.3 kHz 0.16dB 19.4 kHz -0.66dB 19.9 kHz -1.1dB 22.1 kHz -6.9dB Stopband SB 26.1 kHz Passband Ripple PR dB 0.1 Stopband Attenuation SA 73 dB Group Delay (Note 27) GD 19 1/fs Group Delay Distortion 0 GD s ADC Digital Filter (HPF): (Note 28) Frequency Response (Note 26) -3.0dB FR 0.9 Hz 2.7 Hz -0.5dB 6.0 Hz -0.1dB DAC Digital Filter (LPF): Passband (Note 26) PB 0 19.6 kHz 0.1dB 20.0 kHz -0.7dB 22.05 kHz -6.0dB Stopband SB 25.2 kHz Passband Ripple PR dB 0.01 Stopband Attenuation SA 59 dB Group Delay (Note 27) GD 25 1/fs DAC Digital Filter (LPF) + SCF: FR dB Frequency Response: 0 20.0kHz 1.0 DAC Digital Filter (HPF): (Note 28) Frequency Response (Note 26) -3.0dB FR 0.9 Hz 2.7 Hz -0.5dB 6.0 Hz -0.1dB BOOST Filter: (Note 29) Frequency Response MIN FR 20Hz dB 5.76 100Hz dB 2.92 1kHz dB 0.02 MID FR 20Hz dB 10.80 100Hz dB 6.84 1kHz dB 0.13 MAX 20Hz FR dB 16.06 100Hz dB 10.54 1kHz dB 0.37
Note 26. The passband and stopband frequencies scale with fs (system sampling rate). For example, DAC is PB=0.454*fs (@-0.7dB). Each response refers to that of 1kHz. Note 27. The calculated delay time caused by digital filtering. This time is from the input of analog signal to setting of the 16-bit data of both channels from the input register to the output register of the ADC. This time includes the group delay of the HPF. For the DAC, this time is from setting the 16-bit data of both channels from the input register to the output of analog signal. Group delay of DAC part is 25/fs(typ) at PMADL=PMADR bits = "0". Note 28. When PMADL bit = "1" or PMADR bit = "1", the HPF of ADC is enabled but the HPF of DAC is disabled. When PMADL=PMADR bits = "0", PMDAC bit = "1", the HPF of DAC is enabled but the HPF of ADC is disabled. Note 29. These frequency responses scale with fs. If a high-level signal is input, the analog output clips to the full-scale at low frequency.
MS0605-E-00 - 12 -
2007/06
[AK4645EZ]
DC CHARACTERISTICS (Ta=25C; AVDD, DVDD=2.6 3.6V; TVDD=1.6 3.6V; HVDD=2.6 5.25V) Parameter Symbol min High-Level Input Voltage 2.2VTVDD3.6V VIH 70%TVDD 1.6VTVDD<2.2V VIH 75%TVDD Low-Level Input Voltage 2.2VTVDD3.6V VIL 1.6VTVDD<2.2V VIL High-Level Output Voltage VOH (Iout=-200A) TVDD-0.2 Low-Level Output Voltage VOL (Except SDA pin: Iout=200A) (SDA pin: Iout=3mA) VOL Input Leakage Current Iin -
typ -
max 30%TVDD 25%TVDD 0.2 0.4 10
Units V V V V V V V A
SWITCHING CHARACTERISTICS (Ta=25C; AVDD, DVDD=2.6 3.6V; TVDD=1.6 3.6V; HVDD=2.6 5.25V; CL=20pF; unless otherwise specified) Parameter Symbol min typ max Units PLL Master Mode (PLL Reference Clock = MCKI pin) MCKI Input Timing Frequency fCLK 11.2896 27 MHz Pulse Width Low tCLKL 0.4/fCLK ns Pulse Width High tCLKH 0.4/fCLK ns MCKO Output Timing Frequency fMCK 0.2352 12.288 MHz Duty Cycle Except 256fs at fs=32kHz, 29.4kHz dMCK 40 50 60 % 256fs at fs=32kHz, 29.4kHz dMCK 33 % LRCK Output Timing Frequency fs 7.35 48 kHz DSP Mode: Pulse Width High tLRCKH tBCK ns Except DSP Mode: Duty Cycle Duty 50 % BICK Output Timing Period BCKO bit = "0" tBCK 1/(32fs) ns BCKO bit = "1" tBCK 1/(64fs) ns Duty Cycle dBCK 50 % PLL Slave Mode (PLL Reference Clock = MCKI pin) MCKI Input Timing Frequency fCLK 11.2896 27 MHz Pulse Width Low tCLKL 0.4/fCLK ns Pulse Width High tCLKH 0.4/fCLK ns MCKO Output Timing Frequency fMCK 0.2352 12.288 MHz Duty Cycle Except 256fs at fs=32kHz, 29.4kHz dMCK 40 50 60 % 256fs at fs=32kHz, 29.4kHz dMCK 33 % LRCK Input Timing Frequency fs 7.35 48 kHz DSP Mode: Pulse Width High tLRCKH tBCK-60 1/fs - tBCK ns Except DSP Mode: Duty Cycle Duty 45 55 % BICK Input Timing Period tBCK 1/(64fs) 1/(32fs) ns Pulse Width Low tBCKL 0.4 x tBCK ns Pulse Width High tBCKH 0.4 x tBCK ns
MS0605-E-00 - 13 -
2007/06
[AK4645EZ]
Parameter Symbol PLL Slave Mode (PLL Reference Clock = LRCK pin) LRCK Input Timing Frequency fs DSP Mode: Pulse Width High tLRCKH Except DSP Mode: Duty Cycle Duty BICK Input Timing Period tBCK Pulse Width Low tBCKL Pulse Width High tBCKH PLL Slave Mode (PLL Reference Clock = BICK pin) LRCK Input Timing Frequency fs DSP Mode: Pulse Width High tLRCKH Except DSP Mode: Duty Cycle Duty BICK Input Timing Period PLL3-0 bits = "0010" tBCK PLL3-0 bits = "0011" tBCK Pulse Width Low tBCKL Pulse Width High tBCKH External Slave Mode MCKI Input Timing Frequency 256fs fCLK 512fs fCLK 1024fs fCLK Pulse Width Low tCLKL Pulse Width High tCLKH LRCK Input Timing Frequency 256fs fs 512fs fs 1024fs fs DSP Mode: Pulse Width High tLRCKH Except DSP Mode: Duty Cycle Duty BICK Input Timing Period tBCK Pulse Width Low tBCKL Pulse Width High tBCKH External Master Mode MCKI Input Timing Frequency 256fs fCLK 512fs fCLK 1024fs fCLK Pulse Width Low tCLKL Pulse Width High tCLKH LRCK Output Timing Frequency fs DSP Mode: Pulse Width High tLRCKH Except DSP Mode: Duty Cycle Duty BICK Output Timing Period BCKO bit = "0" tBCK BCKO bit = "1" tBCK Duty Cycle dBCK
min
typ
max
Units
7.35 tBCK-60 45 1/(64fs) 130 130
-
48 1/fs - tBCK 55 1/(32fs) -
kHz ns % ns ns ns
7.35 tBCK-60 45 0.4 x tBCK 0.4 x tBCK
1/(32fs) 1/(64fs) -
48 1/fs - tBCK 55 -
kHz ns % ns ns ns ns
1.8816 3.7632 7.5264 0.4/fCLK 0.4/fCLK 7.35 7.35 7.35 tBCK-60 45 312.5 130 130
-
12.288 13.312 13.312 48 26 13 1/fs - tBCK 55 -
MHz MHz MHz ns ns kHz kHz kHz ns % ns ns ns
1.8816 3.7632 7.5264 0.4/fCLK 0.4/fCLK 7.35 -
tBCK 50 1/(32fs) 1/(64fs) 50
12.288 13.312 13.312 48 -
MHz MHz MHz ns ns kHz ns % ns ns %
MS0605-E-00 - 14 -
2007/06
[AK4645EZ]
Parameter Symbol Audio Interface Timing (DSP Mode) Master Mode tDBF LRCK "" to BICK "" (Note 30) tDBF LRCK "" to BICK "" (Note 31) tBSD BICK "" to SDTO (BCKP bit = "0") tBSD BICK "" to SDTO (BCKP bit = "1") SDTI Hold Time tSDH SDTI Setup Time tSDS Slave Mode tLRB LRCK "" to BICK "" (Note 30) tLRB LRCK "" to BICK "" (Note 31) tBLR BICK "" to LRCK "" (Note 30) tBLR BICK "" to LRCK "" (Note 31) tBSD BICK "" to SDTO (BCKP bit = "0") tBSD BICK "" to SDTO (BCKP bit = "1") SDTI Hold Time tSDH SDTI Setup Time tSDS Audio Interface Timing (Right/Left justified & I2S) Master Mode tMBLR BICK "" to LRCK Edge (Note 32) tLRD LRCK Edge to SDTO (MSB) (Except I2S mode) tBSD BICK "" to SDTO SDTI Hold Time tSDH SDTI Setup Time tSDS Slave Mode tLRB LRCK Edge to BICK "" (Note 32) tBLR BICK "" to LRCK Edge (Note 32) tLRD LRCK Edge to SDTO (MSB) (Except I2S mode) tBSD BICK "" to SDTO SDTI Hold Time tSDH SDTI Setup Time tSDS
min
typ
max
Units
0.5 x tBCK - 40 0.5 x tBCK - 40 -70 -70 50 50 0.4 x tBCK 0.4 x tBCK 0.4 x tBCK 0.4 x tBCK 50 50
0.5 x tBCK 0.5 x tBCK -
0.5 x tBCK + 40 0.5 x tBCK + 40 70 70 80 80 -
ns ns ns ns ns ns ns ns ns ns ns ns ns ns
-40 -70 -70 50 50 50 50 50 50
-
40 70 70 80 80 -
ns ns ns ns ns ns ns ns ns ns ns
Note 30. MSBS, BCKP bits = "00" or "11". Note 31. MSBS, BCKP bits = "01" or "10". Note 32. BICK rising edge must not occur at the same time as LRCK edge.
MS0605-E-00 - 15 -
2007/06
[AK4645EZ]
Parameter Symbol min Control Interface Timing (3-wire Serial mode) CCLK Period tCCK 200 CCLK Pulse Width Low tCCKL 80 Pulse Width High tCCKH 80 CDTI Setup Time tCDS 40 CDTI Hold Time tCDH 40 CSN "H" Time tCSW 150 tCSS 50 CSN Edge to CCLK "" (Note 34) tCSH 50 CCLK "" to CSN Edge (Note 34) Control Interface Timing (I2C Bus mode): (Note 33) SCL Clock Frequency fSCL Bus Free Time Between Transmissions tBUF 1.3 Start Condition Hold Time (prior to first clock pulse) tHD:STA 0.6 Clock Low Time tLOW 1.3 Clock High Time tHIGH 0.6 Setup Time for Repeated Start Condition tSU:STA 0.6 SDA Hold Time from SCL Falling (Note 35) tHD:DAT 0 SDA Setup Time from SCL Rising tSU:DAT 0.1 Rise Time of Both SDA and SCL Lines tR Fall Time of Both SDA and SCL Lines tF Setup Time for Stop Condition tSU:STO 0.6 Capacitive Load on Bus Cb Pulse Width of Spike Noise Suppressed by Input Filter tSP 0 Power-down & Reset Timing PDN Pulse Width (Note 36) tPD 150 tPDV PMADL or PMADR "" to SDTO valid (Note 37) 2 Note 33. I C is a registered trademark of Philips Semiconductors. Note 34. CCLK rising edge must not occur at the same time as CSN edge. Note 35. Data must be held long enough to bridge the 300ns-transition time of SCL. Note 36. The AK4645 can be reset by the PDN pin = "L". Note 37. This is the count of LRCK "" from the PMADL or PMADR bit = "1".
typ 1059
max 400 0.3 0.3 400 50 -
Units ns ns ns ns ns ns ns ns kHz s s s s s s s s s s pF ns ns 1/fs
MS0605-E-00 - 16 -
2007/06
[AK4645EZ]
Timing Diagram
1/fCLK VIH MCKI VIL tCLKH 1/fs tCLKL
LRCK tLRCKH tLRCKL
50%TVDD
1/fMCK
Duty = tLRCKH x fs x 100 tLRCKL x fs x 100
MCKO tMCKL
50%TVDD dMCK = tMCKL x fMCK x 100
Figure 3. Clock Timing (PLL/EXT Master mode) Note 38. MCKO is not available at EXT Master mode.
tLRCKH
LRCK tDBF tBCK dBCK BICK (BCKP = "0")
50%TVDD
50%TVDD
BICK (BCKP = "1") tBSD
50%TVDD
SDTO tSDS
MSB tSDH
50%TVDD
VIH SDTI VIL
Figure 4. Audio Interface Timing (PLL/EXT Master mode, DSP mode, MSBS = "0")
MS0605-E-00 - 17 -
2007/06
[AK4645EZ]
tLRCKH
LRCK tDBF tBCK dBCK BICK (BCKP = "1")
50%TVDD
50%TVDD
BICK (BCKP = "0") tBSD SDTO tSDS
50%TVDD
MSB tSDH
50%TVDD
VIH SDTI VIL
Figure 5. Audio Interface Timing (PLL/EXT Master mode, DSP mode, MSBS = "1")
LRCK
50%TVDD
tBLR
tBCKL 50%TVDD tLRD
BICK
tBSD
SDTO tSDS tSDH
50%TVDD
VIH SDTI VIL
Figure 6. Audio Interface Timing (PLL/EXT Master mode, Except DSP mode)
MS0605-E-00 - 18 -
2007/06
[AK4645EZ]
1/fs VIH VIL tLRCKH tBCK VIH BICK (BCKP = "0") tBCKH tBCKL VIH BICK (BCKP = "1") VIL VIL tBLR
LRCK
Figure 7. Clock Timing (PLL Slave mode; PLL Reference Clock = LRCK or BICK pin, DSP mode, MSBS = "0")
1/fs VIH VIL tLRCKH tBCK VIH BICK (BCKP = "1") tBCKH tBCKL VIH BICK (BCKP = "0") VIL VIL tBLR
LRCK
Figure 8. Clock Timing (PLL Slave mode; PLL Reference Clock = LRCK or BICK pin, DSP mode, MSBS = "1")
MS0605-E-00 - 19 -
2007/06
[AK4645EZ]
1/fCLK VIH MCKI VIL tCLKH 1/fs VIH LRCK VIL tLRCKH tBCK tLRCKL Duty = tLRCKH x fs x 100 = tLRCKL x fs x 100 VIH BICK VIL tBCKH fMCK tBCKL tCLKL
MCKO tMCKL
50%TVDD
dMCK = tMCKL x fMCK x 100
Figure 9. Clock Timing (PLL Slave mode; PLL Reference Clock = MCKI pin, Except DSP mode)
tLRCKH VIH LRCK tLRB VIL
VIH BICK (BCKP = "0") VIH BICK (BCKP = "1") tBSD VIL VIL
SDTO
MSB tSDH
50%TVDD
tSDS
VIH SDTI MSB VIL
Figure 10. Audio Interface Timing (PLL Slave mode, DSP mode; MSBS = "0") MS0605-E-00 - 20 2007/06
[AK4645EZ]
tLRCKH VIH LRCK tLRB VIL
VIH BICK (BCKP = "1") VIH BICK (BCKP = "0") tBSD VIL VIL
SDTO
MSB tSDH
50%TVDD
tSDS
VIH SDTI MSB VIL
Figure 11. Audio Interface Timing (PLL Slave mode, DSP mode, MSBS = "1")
1/fCLK VIH MCKI VIL tCLKH 1/fs VIH LRCK VIL tLRCKH tBCK VIH BICK VIL tBCKH tBCKL tLRCKL Duty = tLRCKH x fs x 100 tLRCKL x fs x 100 tCLKL
Figure 12. Clock Timing (EXT Slave mode)
MS0605-E-00 - 21 -
2007/06
[AK4645EZ]
VIH LRCK VIL tBLR tLRB VIH BICK VIL tLRD tBSD
SDTO tSDS
MSB tSDH
50%TVDD
VIH SDTI VIL
Figure 13. Audio Interface Timing (PLL/EXT Slave mode, Except DSP mode)
VIH CSN VIL tCSH tCSS tCCKL tCCKH VIH CCLK VIL tCDS CDTI C1 C0 tCCK tCDH VIH R/W VIL
Figure 14. WRITE Command Input Timing
MS0605-E-00 - 22 -
2007/06
[AK4645EZ]
tCSW VIH CSN VIL tCSH tCSS VIH CCLK VIL
VIH CDTI D2 D1 D0 VIL
Figure 15. WRITE Data Input Timing
SDA
tBUF tLOW tR tHIGH tF tSP
VIH VIL
VIH SCL VIL
tHD:STA Stop Start tHD:DAT tSU:DAT tSU:STA Start tSU:STO Stop
Figure 16. I2C Bus Mode Timing
PMADL bit or PMADR bit tPDV
SDTO
50%TVDD
Figure 17. Power Down & Reset Timing 1
tPD PDN VIL
Figure 18. Power Down & Reset Timing 2
MS0605-E-00 - 23 -
2007/06
[AK4645EZ]
OPERATION OVERVIEW
System Clock
There are the following four clock modes to interface with external devices (Table 2 and Table 3). Mode PMPLL bit M/S bit PLL3-0 bits Figure PLL Master Mode (Note 39) 1 1 Table 5 Figure 19 PLL Slave Mode 1 Table 5 Figure 20 1 0 (PLL Reference Clock: MCKI pin) PLL Slave Mode 2 Figure 21 Table 5 1 0 Figure 22 (PLL Reference Clock: LRCK or BICK pin) EXT Slave Mode 0 0 x Figure 23 EXT Master Mode 0 1 x Figure 24 Note 39. If M/S bit = "1", PMPLL bit = "0" and MCKO bit = "1" during the setting of PLL Master Mode, invalid clocks are output from MCKO pin when MCKO bit is "1". Table 2. Clock Mode Setting (x: Don't care) Mode PLL Master Mode PLL Slave Mode (PLL Reference Clock: MCKI pin) PLL Slave Mode (PLL Reference Clock: LRCK or BICK pin) EXT Slave Mode EXT Master Mode MCKO bit 0 1 0 1 0 0 0 MCKO pin "L" Selected by PS1-0 bits "L" Selected by PS1-0 bits "L" "L" "L" MCKI pin Selected by PLL3-0 bits Selected by PLL3-0 bits GND Selected by FS1-0 bits Selected by FS1-0 bits BICK pin Output (Selected by BCKO bit) Input ( 32fs) Input (Selected by PLL3-0 bits) Input ( 32fs) Output (Selected by BCKO bit) LRCK pin Output (1fs) Input (1fs) Input (1fs) Input (1fs) Output (1fs)
Table 3. Clock pins state in Clock Mode
Master Mode/Slave Mode
The M/S bit selects either master or slave mode. M/S bit = "1" selects master mode and "0" selects slave mode. When the AK4645 is power-down mode (PDN pin = "L") and exits reset state, the AK4645 is slave mode. After exiting reset state, the AK4645 goes to master mode by changing M/S bit = "1". When the AK4645 is used on master mode, LRCK and BICK pins are a floating state until M/S bit becomes "1". LRCK and BICK pins of the AK4645 should be pulled-down or pulled-up by the resistor (about 100k) externally to avoid the floating state. M/S bit Mode 0 Slave Mode 1 Master Mode Table 4. Select Master/Slave Mode
Default
MS0605-E-00 - 24 -
2007/06
[AK4645EZ]
PLL Mode (AIN3 bit = "0", PMPLL bit = "1")
When PMPLL bit is "1", a fully integrated analog phase locked loop (PLL) generates a clock that is selected by the PLL3-0 and FS3-0 bits. The PLL lock time is shown in Table 5, whenever the AK4645 is supplied to a stable clocks after PLL is powered-up (PMPLL bit = "0" "1") or sampling frequency changes. When AIN3 bit = "1", the PLL is not available. 1) Setting of PLL Mode
Mode
PLL3 bit 0 0 0 0 0 0 0 1 1 1 1 1
PLL2 bit 0 0 0 1 1 1 1 0 1 1 1 1
Others
PLL1 bit 0 1 1 0 0 1 1 0 0 0 1 1
PLL0 bit 0 0 1 0 1 0 1 0 0 1 0 1
PLL Reference Clock Input Pin LRCK pin BICK pin BICK pin
Input Frequency 1fs 32fs 64fs
0 2 3 4 5 6 7 8 12 13 14 15
Others
MCKI pin 11.2896MHz MCKI pin 12.288MHz MCKI pin 12MHz MCKI pin 24MHz MCKI pin 19.2MHz MCKI pin 13.5MHz MCKI pin 27MHz MCKI pin 13MHz MCKI pin 26MHz N/A Table 5. Setting of PLL Mode (*fs: Sampling Frequency)
R and C of VCOC pin R[] C[F] 6.8k 220n 10k 4.7n 10k 10n 10k 4.7n 10k 10n 10k 4.7n 10k 4.7n 10k 4.7n 10k 4.7n 10k 4.7n 10k 10n 10k 10n 10k 220n 10k 220n
PLL Lock Time (max) 160ms 2ms 4ms 2ms 4ms 40ms 40ms 40ms 40ms 40ms 40ms 40ms 60ms 60ms Default
2) Setting of sampling frequency in PLL Mode When PLL reference clock input is MCKI pin, the sampling frequency is selected by FS3-0 bits as defined in Table 6. Mode FS3 bit FS2 bit FS1 bit FS0 bit Sampling Frequency 0 0 0 0 0 8kHz Default 1 0 0 0 1 12kHz 2 0 0 1 0 16kHz 3 0 0 1 1 24kHz 4 0 1 0 0 7.35kHz 5 0 1 0 1 11.025kHz 6 0 1 1 0 14.7kHz 7 0 1 1 1 22.05kHz 10 1 0 1 0 32kHz 11 1 0 1 1 48kHz 14 1 1 1 0 29.4kHz 15 1 1 1 1 44.1kHz Others Others N/A Table 6. Setting of Sampling Frequency at PMPLL bit = "1" (Reference Clock = MCKI pin)
MS0605-E-00 - 25 -
2007/06
[AK4645EZ]
When PLL reference clock input is LRCK or BICK pin, the sampling frequency is selected by FS3 and FS1-0 bits. (Table 7). Mode FS3 bit FS2 bit FS1 bit FS0 bit Sampling Frequency Range 0 Don't care 0 0 0 Default 7.35kHz fs 8kHz 0 Don't care 1 1 0 8kHz < fs 12kHz 0 Don't care 0 2 1 12kHz < fs 16kHz 0 Don't care 1 3 1 16kHz < fs 24kHz 1 Don't care 0 6 1 24kHz < fs 32kHz 1 Don't care 1 7 1 32kHz < fs 48kHz Others Others N/A Table 7. Setting of Sampling Frequency at PMPLL bit = "1" (Reference Clock = LRCK or BICK pin)
PLL Unlock State
1) PLL Master Mode (AIN3 bit = "0"; PMPLL bit = "1", M/S bit = "1") In this mode, LRCK and BICK pins go to "L" and irregular frequency clock is output from MCKO pins at MCKO bit is "1" before the PLL goes to lock state after PMPLL bit = "0" "1". If MCKO bit is "0", MCKO pin goes to "L" (Table 8). After the PLL is locked, the first period of LRCK and BICK may be invalid clock but these clocks return to normal state after a period of 1/fs. When sampling frequency is changed, BICK and LRCK pins do not output irregular frequency clocks but go to "L" by setting PMPLL bit to "0". MCKO pin BICK pin MCKO bit = "0" MCKO bit = "1" After that PMPLL bit "0" "1" "L" Output Invalid "L" Output PLL Unlock (except case above) "L" Output Invalid Invalid PLL Lock "L" Output Table 10 Table 11 Table 8. Clock Operation at PLL Master Mode (PMPLL bit = "1", M/S bit = "1") PLL State 2) PLL Slave Mode (AIN3 bit = "0", PMPLL bit = "1", M/S bit = "0") In this mode, an invalid clock is output from MCKO pin before the PLL goes to lock state after PMPLL bit = "0" "1". Then, the clock selected by Table 10 is output from MCKO pin when PLL is locked. ADC and DAC output invalid data when the PLL is unlocked. For DAC, the output signal should be muted by writing "0" to DACL and DACH bits. MCKO pin MCKO bit = "0" MCKO bit = "1" Just after PMPLL bit "0" "1" "L" Output Invalid PLL Unlock (except case above) "L" Output Invalid PLL Lock "L" Output Output Table 9. Clock Operation at PLL Slave Mode (PMPLL bit = "0", M/S bit = "0") PLL State LRCK pin "L" Output Invalid 1fs Output
MS0605-E-00 - 26 -
2007/06
[AK4645EZ]
PLL Master Mode (AIN3 bit = "0", PMPLL bit = "1", M/S bit = "1")
When an external clock (11.2896MHz, 12MHz, 12.288MHz, 13MHz, 13.5MHz, 19.2MHz, 24MHz, 26MHz or 27MHz) is input to MCKI pin, the MCKO, BICK and LRCK clocks are generated by an internal PLL circuit. The MCKO output frequency is selected by PS1-0 bits (Table 10) and the output is enabled by MCKO bit. The BICK output frequency is selected between 32fs or 64fs, by BCKO bit (Table 11).
11.2896MHz, 12MHz, 12.288MHz, 13MHz, 13.5MHz, 19.2MHz, 24MHz, 26MHz, 27MHz
AK4645
MCKI MCKO BICK LRCK SDTO SDTI
DSP or P
256fs/128fs/64fs/32fs 32fs, 64fs 1fs
MCLK BCLK LRCK SDTI SDTO
Figure 19. PLL Master Mode Mode PS1 bit PS0 bit MCKO pin 0 0 0 256fs Default 1 0 1 128fs 2 1 0 64fs 3 1 1 32fs Table 10. MCKO Output Frequency (PLL Mode, MCKO bit = "1") BICK Output Frequency 0 32fs Default 1 64fs Table 11. BICK Output Frequency at Master Mode BCKO bit
MS0605-E-00 - 27 -
2007/06
[AK4645EZ]
PLL Slave Mode (AIN3 bit = "0", PMPLL bit = "1", M/S bit = "0")
A reference clock of PLL is selected among the input clocks to MCKI, BICK or LRCK pin. The required clock to the AK4645 is generated by an internal PLL circuit. Input frequency is selected by PLL3-0 bits (Table 5). a) PLL reference clock: MCKI pin BICK and LRCK inputs should be synchronized with MCKO output. The phase between MCKO and LRCK dose not matter. MCKO pin outputs the frequency selected by PS1-0 bits (Table 10) and the output is enabled by MCKO bit. Sampling frequency can be selected by FS3-0 bits (Table 6).
11.2896MHz, 12MHz, 12.288MHz, 13MHz, 13.5MHz, 19.2MHz, 24MHz, 26MHz, 27MHz
AK4645
MCKI MCKO BICK LRCK SDTO SDTI
DSP or P
256fs/128fs/64fs/32fs 32fs 1fs
MCLK BCLK LRCK SDTI SDTO
Figure 20. PLL Slave Mode 1 (PLL Reference Clock: MCKI pin)
MS0605-E-00 - 28 -
2007/06
[AK4645EZ]
b) PLL reference clock: BICK or LRCK pin Sampling frequency corresponds to 7.35kHz to 48kHz by changing FS3-0 bits (Table 7).
AK4645
MCKO MCKI BICK LRCK SDTO SDTI 32fs or 64fs 1fs BCLK LRCK SDTI SDTO
DSP or P
Figure 21. PLL Slave Mode 2 (PLL Reference Clock: BICK pin)
AK4645
MCKO MCKI BICK LRCK SDTO SDTI 32fs 1fs BCLK LRCK SDTI SDTO
DSP or P
Figure 22. PLL Slave Mode 2 (PLL Reference Clock: LRCK pin) The external clocks (MCKI, BICK and LRCK) should always be present whenever the ADC or DAC is in operation (PMADL bit = "1", PMADR bit = "1" or PMDAC bit = "1"). If these clocks are not provided, the AK4645 may draw excess current and it is not possible to operate properly because utilizes dynamic refreshed logic internally. If the external clocks are not present, the ADC and DAC should be in the power-down mode (PMADL=PMADR=PMDAC bits = "0").
MS0605-E-00 - 29 -
2007/06
[AK4645EZ]
EXT Slave Mode (PMPLL bit = "0", M/S bit = "0")
When PMPLL bit is "0", the AK4645 becomes EXT mode. Master clock is input from MCKI pin, the internal PLL circuit is not operated. This mode is compatible with I/F of the normal audio CODEC. The clocks required to operate are MCKI (256fs, 512fs or 1024fs), LRCK (fs) and BICK (32fs). The master clock (MCKI) should be synchronized with LRCK. The phase between these clocks does not matter. The input frequency of MCKI is selected by FS1-0 bits (Table 12). Mode 0 1 2 3 MCKI Input Sampling Frequency Frequency Range Don't care 0 0 256fs 7.35kHz 48kHz Don't care 0 1 1024fs 7.35kHz 13kHz Don't care 1 0 256fs 7.35kHz 48kHz Don't care 1 1 512fs 7.35kHz 26kHz Table 12. MCKI Frequency at EXT Slave Mode (PMPLL bit = "0", M/S bit = "0") FS3-2 bits FS1 bit FS0 bit
Default
The S/N of the DAC at low sampling frequencies is worse than at high sampling frequencies due to out-of-band noise. The out-of-band noise can be improved by using higher frequency of the master clock. The S/N of the DAC output through LOUT/ROUT pins at fs=8kHz is shown in Table 13. S/N (fs=8kHz, 20kHzLPF + A-weighted) 256fs 83dB 512fs 93dB 1024fs 93dB Table 13. Relationship between MCKI and S/N of LOUT/ROUT pins MCKI The external clocks (MCKI, BICK and LRCK) should always be present whenever the ADC or DAC is in operation (PMADL bit = "1", PMADR bit = "1" or PMDAC bit = "1"). If these clocks are not provided, the AK4645 may draw excess current and it is not possible to operate properly because utilizes dynamic refreshed logic internally. If the external clocks are not present, the ADC and DAC should be in the power-down mode (PMADL=PMADR=PMDAC bits = "0").
AK4645
MCKO 256fs, 512fs or 1024fs MCKI BICK LRCK SDTO SDTI 32fs 1fs MCLK BCLK LRCK SDTI SDTO
DSP or P
Figure 23. EXT Slave Mode
MS0605-E-00 - 30 -
2007/06
[AK4645EZ]
EXT Master Mode (PMPLL bit = "0", M/S bit = "1")
The AK4645 becomes EXT Master Mode by setting PMPLL bit = "0" and M/S bit = "1". Master clock is input from MCKI pin, the internal PLL circuit is not operated. The clock required to operate is MCKI (256fs, 512fs or 1024fs). The input frequency of MCKI is selected by FS1-0 bits (Table 14). Mode 0 1 2 3 MCKI Input Sampling Frequency Frequency Range Don't care 0 0 256fs 7.35kHz 48kHz Don't care 0 1 1024fs 7.35kHz 13kHz Don't care 1 0 256fs 7.35kHz 48kHz Don't care 1 1 512fs 7.35kHz 26kHz Table 14. MCKI Frequency at EXT Master Mode (PMPLL bit = "0", M/S bit = "1") FS3-2 bits FS1 bit FS0 bit
Default
The S/N of the DAC at low sampling frequencies is worse than at high sampling frequencies due to out-of-band noise. The out-of-band noise can be improved by using higher frequency of the master clock. The S/N of the DAC output through LOUT/ROUT pins at fs=8kHz is shown in Table 15. S/N (fs=8kHz, 20kHzLPF + A-weighted) 256fs 83dB 512fs 93dB 1024fs 93dB Table 15. Relationship between MCKI and S/N of LOUT/ROUT pins MCKI MCKI should always be present whenever the ADC or DAC is in operation (PMADL bit = "1", PMADR bit = "1" or PMDAC bit = "1"). If MCKI is not provided, the AK4645 may draw excess current and it is not possible to operate properly because utilizes dynamic refreshed logic internally. If MCKI is not present, the ADC and DAC should be in the power-down mode (PMADL=PMADR=PMDAC bits = "0").
AK4645
MCKO 256fs, 512fs or 1024fs MCKI BICK LRCK SDTO SDTI 32fs or 64fs 1fs MCLK BCLK LRCK SDTI SDTO
DSP or P
Figure 24. EXT Master Mode BICK Output Frequency 0 32fs Default 1 64fs Table 16. BICK Output Frequency at Master Mode BCKO bit
MS0605-E-00 - 31 -
2007/06
[AK4645EZ]
System Reset
Upon power-up, the AK4645 should be reset by bringing the PDN pin = "L". This ensures that all internal registers reset to their initial values. The ADC enters an initialization cycle that starts when the PMADL or PMADR bit is changed from "0" to "1" at PMDAC bits is "0". The initialization cycle time is 1059/fs=24ms@fs=44.1kHz. During the initialization cycle, the ADC digital data of both channels is forced to output a 2's compliment, "0". The ADC output reflects the analog input signal after the initialization cycle is complete. When PMDAC bit is "1", the ADC does not require an initialization cycle. The DAC enters an initialization cycle that starts when the PMDAC bit is changed from "0" to "1" at PMADL and PMADR bits are "0". The initialization cycle time is 1059/fs=24ms@fs=44.1kHz. During the initialization cycle, the DAC input digital data of both channels are internally forced to a 2's compliment, "0". The DAC output reflects the digital input data after the initialization cycle is completed. When PMADL or PMADR bit is "1", the DAC does not require an initialization cycle.
Audio Interface Format
Four types of data formats are available and are selected by setting the DIF1-0 bits (Table 17). In all modes, the serial data is MSB first, 2's complement format. Audio interface formats can be used in both master and slave modes. LRCK and BICK are output from the AK4645 in master mode, but must be input to the AK4645 in slave mode. Mode 0 1 2 3 DIF1 bit 0 0 1 1 DIF0 bit 0 1 0 1 SDTO (ADC) SDTI (DAC) DSP Mode DSP Mode MSB justified LSB justified MSB justified MSB justified I2S compatible I2S compatible Table 17. Audio Interface Format BICK 32fs 32fs 32fs 32fs Figure Table 18 Figure 29 Figure 30 Figure 31
Default
In modes 1, 2 and 3, the SDTO is clocked out on the falling edge ("") of BICK and the SDTI is latched on the rising edge (""). In Modes 0 (DSP mode), the audio I/F timing is changed by BCKP and MSBS bits (Table 18). DIF1 DIF0 MSBS 0 BCKP 0 Audio Interface Format MSB of SDTO is output by the rising edge ("") of the first BICK after the rising edge ("") of LRCK. MSB of SDTI is latched by the falling edge ("") of the BICK just after the output timing of SDTO's MSB. MSB of SDTO is output by the falling edge ("") of the first BICK after the rising edge ("") of LRCK. MSB of SDTI is latched by the rising edge ("") of the BICK just after the output timing of SDTO's MSB. MSB of SDTO is output by next rising edge ("") of the falling edge ("") of the first BICK after the rising edge ("") of LRCK. MSB of SDTI is latched by the falling edge ("") of the BICK just after the output timing of SDTO's MSB. MSB of SDTO is output by next falling edge ("") of the rising edge ("") of the first BICK after the rising edge ("") of LRCK. MSB of SDTI is latched by the rising edge ("") of the BICK just after the output timing of SDTO's MSB. Table 18. Audio Interface Format in Mode 0 Figure Figure 25 Default
0 0 0 1
1
Figure 26
0
Figure 27
1
1
Figure 28
If 16-bit data that ADC outputs is converted to 8-bit data by removing LSB 8-bit, "-1" at 16bit data is converted to "-1" at 8-bit data. And when the DAC playbacks this 8-bit data, "-1" at 8-bit data will be converted to "-256" at 16-bit data and this is a large offset. This offset can be removed by adding the offset of "128" to 16-bit data before converting to 8-bit data.
MS0605-E-00 - 32 -
2007/06
[AK4645EZ]
LRCK
(Master)
LRCK
(Slave)
15 0 1 2 8 9 10 11 12 13 14 15 16 17 18 24 25 26 27 26 29 30 31 0
BICK(32fs)
Lch Rch
8 7 6 5 4 3 2 1 0 15 14 8 7 6 5 4 3 2 1 0
SDTO(o) SDTI(i)
15
0
15 14
Lch
0
0
Rch
8
14
15 14
1 2
7
15
6
16
5
17
4
18
3
2
30
1
31
0
15 14
32 33 34
8
46
7
47
6
48
5
49
4
50
3
2
62
1
63
0
BICK(64fs)
Lch Rch
2 1 0 15 14 2 1 0
SDTO(o) SDTI(i)
15 14
Lch
15 14 2 1 0
Rch
15 14 2 1 0
1/fs 15:MSB, 0:LSB
Figure 25. Mode 0 Timing (BCKP = "0", MSBS = "0")
LRCK
(Master)
LRCK
(Slave)
15 0 1 2 8 9 10 11 12 13 14 15 16 17 18 24 25 26 27 26 29 30 31 0
BICK(32fs)
Lch Rch
8 7 6 5 4 3 2 1 0 15 14 8 7 6 5 4 3 2 1 0
SDTO(o) SDTI(i)
15
0
15 14
Lch
0
0
Rch
8
14
15 14
1 2
7
15
6
16
5
17
4
18
3
2
30
1
31
0
15 14
32 33 34
8
46
7
47
6
48
5
49
4
50
3
2
62
1
63
0
BICK(64fs)
Lch Rch
2 1 0 15 14 2 1 0
SDTO(o) SDTI(i)
15 14
Lch
15 14 2 1 0
Rch
15 14 2 1 0
1/fs 15:MSB, 0:LSB
Figure 26. Mode 0 Timing (BCKP = "1", MSBS = "0")
MS0605-E-00 - 33 -
2007/06
[AK4645EZ]
LRCK
(Master)
LRCK
(Slave)
15 0 1 2 8 9 10 11 12 13 14 15 16 17 18 24 25 26 27 26 29 30 31 0
BICK(32fs)
Lch Rch
8 7 6 5 4 3 2 1 0 15 14 8 7 6 5 4 3 2 1 0
SDTO(o) SDTI(i)
15
0
15 14
Lch
0
0
Rch
8
14
15 14
1 2
7
15
6
16
5
17
4
18
3
2
30
1
31
0
15 14
32 33 34
8
46
7
47
6
48
5
49
4
50
3
2
62
1
63
0
BICK(64fs)
Lch Rch
2 1 0 15 14 2 1 0
SDTO(o) SDTI(i)
15 14
Lch
15 14 2 1 0
Rch
15 14 2 1 0
1/fs 15:MSB, 0:LSB
Figure 27. Mode 0 Timing (BCKP = "0", MSBS = "1")
LRCK
(Master)
LRCK
(Slave)
15 0 1 2 8 9 10 11 12 13 14 15 16 17 18 24 25 26 27 26 29 30 31 0
BICK(32fs)
Lch Rch
8 7 6 5 4 3 2 1 0 15 14 8 7 6 5 4 3 2 1 0
SDTO(o) SDTI(i)
15
0
15 14
Lch
0
0
Rch
8
14
15 14
1 2
7
15
6
16
5
17
4
18
3
2
30
1
31
0
15 14
32 33 34
8
46
7
47
6
48
5
49
4
50
3
2
62
1
63
0
BICK(64fs)
Lch Rch
2 1 0 15 14 2 1 0
SDTO(o) SDTI(i)
15 14
Lch
15 14 2 1 0
Rch
15 14 2 1 0
1/fs 15:MSB, 0:LSB
Figure 28. Mode 0 Timing (BCKP = "1", MSBS = "1")
MS0605-E-00 - 34 -
2007/06
[AK4645EZ]
LRCK
0123 9 10 11 12 13 14 15 0 1 2 3 9 10 11 12 13 14 15 0 1
BICK(32fs) SDTO(o) SDTI(i) BICK(64fs) SDTO(o) SDTI(i)
15 14 13 Don't Care 15:MSB, 0:LSB Lch Data Rch Data 10 15 14 10 15 14 13 Don't Care 10 15 14 210 15 15 14 13 15 14 13 0123 7 6 5 4 3 2 1 0 15 14 13 7 6 5 4 3 2 1 0 15 14 13 15 16 17 18 31 0 1 2 3 7 6 5 4 3 2 1 0 15 7 6 5 4 3 2 1 0 15 15 16 17 18 31 0 1
Figure 29. Mode 1 Timing
LRCK
0123 9 10 11 12 13 14 15 0 1 2 3 9 10 11 12 13 14 15 0 1
BICK(32fs) SDTO(o) SDTI(i) BICK(64fs) SDTO(o) SDTI(i)
15 14 13 15 14 13 15:MSB, 0:LSB Lch Data Rch Data 10 10 Don't Care 15 14 13 15 14 13 10 10 Don't Care 15 15 15 14 13 15 14 13 0123 7 6 5 4 3 2 1 0 15 14 13 7 6 5 4 3 2 1 0 15 14 13 15 16 17 18 31 0 1 2 3 7 6 5 4 3 2 1 0 15 7 6 5 4 3 2 1 0 15 15 16 17 18 31 0 1
Figure 30. Mode 2 Timing
MS0605-E-00 - 35 -
2007/06
[AK4645EZ]
LRCK
0123 9 10 11 12 13 14 15 0 1 2 3 9 10 11 12 13 14 15 0 1
BICK(32fs) SDTO(o) SDTI(i) BICK(64fs) SDTO(o) SDTI(i)
15 14 15 14 210 210 Don't Care 15 14 15 14 210 210 Don't Care 0 15 14 0 15 14 0123 8 7 6 5 4 3 2 1 0 15 14 8 7 6 5 4 3 2 1 0 15 14 15 16 17 18 31 0 1 2 3 876543210 876543210 15 16 17 18 31 0 1
15:MSB, 0:LSB Lch Data Rch Data
Figure 31. Mode 3 Timing
Mono/Stereo Mode
PMADL, PMADR and MIX bits set mono/stereo ADC operation. When MIX bit = "1", EQ and FIL3 bits should be set to "0". ALC operation (ALC bit = "1") or digital volume operation (ALC bit = "0") is applied to the data in Table 19. PMADL bit 0 0 1 1 PMADR bit 0 1 0 MIX bit ADC Lch data ADC Rch data x All "0" All "0" x Rch Input Signal Rch Input Signal x Lch Input Signal Lch Input Signal 0 Lch Input Signal Rch Input Signal 1 1 (L+R)/2 (L+R)/2 Table 19. Mono/Stereo ADC operation (x: Don't care)
Default
Digital High Pass Filter
The AK4645 has a digital high pass filter for DC offset cancellation. The cut-off frequency of the HPF is 0.9Hz (@fs=44.1kHz) and scales with sampling rate (fs). When PMADL bit = "1" or PMADR bit = "1", the HPF of ADC is enabled but the HPF of DAC is disabled. When PMADL=PMADR bits = "0", PMDAC bit = "1", the HPF of DAC is enabled but the HPF of ADC is disabled.
MS0605-E-00 - 36 -
2007/06
[AK4645EZ]
MIC/LINE Input Selector
The AK4645 has input selector for MIC-Amp. When MDIF1 and MDIF2 bits are "0", INL1-0 and INR1-0 bits select LIN1/LIN2/LIN3/LIN4 and RIN1/RIN2/RIN3/RIN4, respectively. When MDIF1 and MDIF2 bits are "1", LIN1, RIN1, LIN2 and RIN2 pins become IN1-, IN1+, IN2+ and IN2- pins respectively. In this case, full-differential input is available (Figure 33). When full-differential input is used, the signal should not be input to the pins marked by "X" in Table 21. MDIF1 bit 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 Others MDIF2 bit 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 1 INL1 bit 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 1 1 0 0 0 0 INL0 bit 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 0 0 0 0 INR1 bit 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 0 0 1 1 0 INR0 bit 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 0 0 1 0 1 0 Lch LIN1 LIN1 LIN1 LIN1 LIN2 LIN2 LIN2 LIN2 LIN3 LIN3 LIN3 LIN3 LIN4 LIN4 LIN4 LIN4 LIN1 LIN3 LIN4 IN1+/- IN1+/- IN1+/- IN1+/- N/A Rch RIN1 RIN2 RIN3 RIN4 RIN1 RIN2 RIN3 RIN4 RIN1 RIN2 RIN3 RIN4 RIN1 RIN2 RIN3 RIN4 IN2+/- IN2+/- IN2+/- RIN2 RIN3 RIN4 IN2+/- N/A
Default
Table 20. MIC/Line In Path Select Register AIN3 bit 0 0 0 0 1 1 1 1 Pin RIN2 LIN1 MIN VCOC LIN4 RIN1 LIN2 MDIF1 bit MDIF2 bit LIN3 RIN3 IN4+ IN1+ IN2+ IN2- IN1- 0 0 O O O O O O 0 1 O X O O O O 1 0 O O X O O X 1 1 O O O O O X 0 0 O O O O O O O 0 1 O X O O O X O 1 0 O O X O X O X 1 1 O O O O X X X Table 21. Handling of MIC/Line Input Pins ("-": N/A; "X": Signal should not be input.)
RIN4 IN4- O X O X O X O X
MS0605-E-00 - 37 -
2007/06
[AK4645EZ]
AK4645
INL1-0 bits LIN1/IN1- pin ADC Lch
RIN1/IN1+ pin MDIF1 bit MIC-Amp
INR1-0 bits RIN2/IN2- pin LIN2/IN2+ pin MDIF2 bit MIN/LIN3 pin VCOC/RIN3 pin MICR3 bit MICL3 bit MIC-Amp These blocks are not available at PLL mode. ADC Rch
LIN4/IN4+ pin RIN4/IN4- pin PMAINR2 bit PMAINR4 bit PMAINL2 bit PMAINL4 bit
Lineout, HP-Amp
Figure 32. Mic/Line Input Selector
AK4645 MPWR pin 1k IN1- pin IN1+ pin 1k
MIC-Amp A/D SDTO pin
Figure 33. Connection Example for Full-differential Mic Input (MDIF1/2 bits = "1")

In case that IN1+/- pins are used as full-differential mic input and LIN2/RIN2 pins are used as stereo line input, it is recommended that the following two modes are set by register setting according to each case. MDIF1 bit 1 0 MDIF2 bit 0 0 INL1 bit INL0 bit INR1 bit INR0 bit 0 0 0 1 0 1 0 1 Table 22. MIC/Line In Path Select Example Lch IN1+/- LIN2 Rch RIN2 RIN2
MS0605-E-00 - 38 -
PMAINR3 bit
PMAINL3 bit
2007/06
[AK4645EZ]
MIC Gain Amplifier
The AK4645 has a gain amplifier for microphone input. The gain of MIC-Amp is selected by the MGAIN1-0 bits (Table 23). The typical input impedance is 60k(typ)@MGAIN1-0 bits = "00" or 30k(typ)@MGAIN1-0 bits = "01", "10" or "11". MGAIN1 bit 0 0 1 1 MGAIN0 bit Input Gain 0 0dB 1 +20dB 0 +26dB 1 +32dB Table 23. Mic Input Gain
Default
MIC Power
When PMMP bit = "1", the MPWR pin supplies power for the microphone. This output voltage is typically 0.75 x AVDD and the load resistance is minimum 0.5k. In case of using two sets of stereo mic, the load resistance is minimum 2k for each channel. No capacitor must not be connected directly to MPWR pin (Figure 34). PMMP bit MPWR pin 0 Hi-Z 1 Output Table 24. MIC Power
MIC Power MPWR pin
Default
2k
2k
2k
2k
Microphone LIN1 pin Microphone RIN1 pin Microphone LIN2 pin Microphone RIN2 pin
Figure 34. MIC Block Circuit
MS0605-E-00 - 39 -
2007/06
[AK4645EZ]
Digital EQ/HPF/LPF
The AK4645 performs wind-noise reduction filter, stereo separation emphasis, gain compensation and ALC (Automatic Level Control) by digital domain for A/D converted data (Figure 35). FIL1, FIL3 and EQ blocks are IIR filters of 1st order. The filter coefficient of FIL3, EQ and FIL1 blocks can be set to any value. Refer to the section of "ALC operation" about ALC. When only DAC is powered-up, digital EQ/HPF/LPF circuit operates at playback path. When only ADC is powered-up or both ADC and DAC are powered-up, digital EQ/HPF/LPF circuit operates at recording path. Even if the path is switched from recording to playback, the register setting of filter coefficient at recording remains. Therefore, FIL3, EQ, FIL1 and GN1-0 bits should be set to "0" if digital EQ/HPF/LPF is not used for playback path. PMADL bit, PMADR bit LOOP bit Status Digital EQ/HPF/LPF x Power-down Power-down "00" x Playback Playback path x Recording Recording path "01", "10" or "11" 0 Recording & Playback Recording path 1 1 Recording Monitor Playback Recording path Note 40. Stereo separation emphasis circuit is effective only at stereo operation. Table 25. Digital EQ/HPF/LPF Cirtcuit Setting (x: Don't care) PMDAC bit 0 1 0
Default
FIL3 coefficient also sets the attenuation of the stereo separation emphasis. The combination of GN1-0 bit (Table 26) and EQ coefficient set the compensation gain. FIL1 and FIL3 blocks become HPF when F1AS and F3AS bits are "0" and become LPF when F1AS and F3AS bits are "1", respectively. When EQ and FIL1 bits are "0", EQ and FIL1 blocks become "through" (0dB). When FIL3 bit is "0", FIL3 block become "MUTE". When each filter coefficient is changed, each filter should be set to "through" ("MUTE" in case of FIL3). When MIX bit = "1", only FIL1 is available. In this case, EQ and FIL3 bits should be set to "0".
Wind-noise reduction Stereo separation emphasis Gain compensation
FIL1
An y coefficient F1A13-0 F1B13-0 F1AS
FIL3
An y coefficient 0dB -10dB F3A13-0 MUTE F3B13-0 (set by F3AS FIL3 coefficient)
EQ
Gain
ALC
An y coefficient GN1-0 EQA15-0 +24/+12/0dB EQB13-0 EQC15-0 +12dB 0dB
Figure 35. Digital EQ/HPF/LPF GN1 GN0 Gain 0 0 0dB Default 0 1 +12dB 1 x +24dB Table 26. Gain select of gain block (x: Don't care)
MS0605-E-00 - 40 -
2007/06
[AK4645EZ]
[Filter Coefficient Setting] 1) When FIL1 and FIL3 are set to "HPF" fs: Sampling frequency fc: Cut-off frequency f: Input signal frequency K: Filter gain [dB] (Filter gain of should be set to 0dB.) Register setting FIL1: F1AS bit = "0", F1A[13:0] bits =A, F1B[13:0] bits =B FIL3: F3AS bit = "0", F3A[13:0] bits =A, F3B[13:0] bits =B (MSB=F1A13, F1B13, F3A13, F3B13; LSB=F1A0, F1B0, F3A0, F3B0)
1 / tan (fc/fs) A = 10K/20 x 1 + 1 / tan (fc/fs) , B= 1 + 1 / tan (fc/fs) 1 - 1 / tan (fc/fs)
Transfer function
1 - z -1 H(z) = A 1 + Bz -1 M(f) = A
Amplitude
2 - 2cos (2f/fs) 1 + B2 + 2Bcos (2f/fs) (f) = tan -1
Phase
(B+1)sin (2f/fs) 1 - B + (B-1)cos (2f/fs)
2) When FIL1 and FIL3 are set to "LPF" fs: Sampling frequency fc: Cut-off frequency f: Input signal frequency K: Filter gain [dB] (Filter gain of FIL1 should be set to 0dB.) Register setting FIL1: F1AS bit = "1", F1A[13:0] bits =A, F1B[13:0] bits =B FIL3: F3AS bit = "1", F3A[13:0] bits =A, F3B[13:0] bits =B (MSB=F1A13, F1B13, F3A13, F3B13; LSB=F1A0, F1B0, F3A0, F3B0)
1 A = 10K/20 x 1 + 1 / tan (fc/fs) , B= 1 + 1 / tan (fc/fs) 1 - 1 / tan (fc/fs)
Transfer function
1 + z -1 H(z) = A 1 + Bz -1 M(f) = A
Amplitude
2 + 2cos (2f/fs) 1 + B2 + 2Bcos (2f/fs) (f) = tan -1
Phase
(B-1)sin (2f/fs) 1 + B + (B+1)cos (2f/fs)
MS0605-E-00 - 41 -
2007/06
[AK4645EZ]
3) EQ fs: Sampling frequency fc1: Pole frequency fc2: Zero-point frequency f: Input signal frequency K: Filter gain [dB] (Maximum +12dB) Register setting EQA[15:0] bits =A, EQB[13:0] bits =B, EQC[15:0] bits =C (MSB=EQA15, EQB13, EQC15; LSB=EQA0, EQB0, EQC0)
A = 10K/20 x 1 + 1 / tan (fc2/fs) , 1 + 1 / tan (fc1/fs) B= 1 + 1 / tan (fc1/fs) 1 - 1 / tan (fc1/fs) , C =10K/20 x 1 - 1 / tan (fc2/fs) 1 + 1 / tan (fc1/fs)
Transfer function
A + Cz H(z) =
-1
Amplitude
A + C + 2ACcos (2f/fs) M(f) = 1 + B2 + 2Bcos (2f/fs)
2 2
Phase
(f) = tan -1 (AB-C)sin (2f/fs) A + BC + (AB+C)cos (2f/fs)
1 + Bz -1
[Translation the filter coefficient calculated by the equations above from real number to binary code (2's complement)] X = (Real number of filter coefficient calculated by the equations above) x 213 X should be rounded to integer, and then should be translated to binary code (2's complement). MSB of each filter coefficient setting register is sine bit.
[Filter Coefficient Setting Example] 1) FIL1 block Example: HPF, fs=44.1kHz, fc=100Hz F1AS bit = "0" F1A[13:0] bits = 01 1111 1100 0110 F1B[13:0] bits = 10 0000 0111 0100 2) EQ block Example: fs=44.1kHz, fc1=300Hz, fc2=3000Hz, Gain=+8dB
Gain[dB] +8dB
fc1
fc2
Frequency
EQA[15:0] bits = 0000 1001 0110 1110 EQB[13:0] bits = 10 0001 0101 1001 EQC[15:0] bits = 1111 1001 1110 1111
MS0605-E-00 - 42 -
2007/06
[AK4645EZ]
ALC Operation
The ALC (Automatic Level Control) is operated by ALC block when ALC bit is "1". When only DAC is powered-up, ALC circuit operates at playback path. When only ADC is powered-up or both ADC and DAC are powered-up, ALC circuit operates at recording path. PMADL bit, PMADR bit "00" "01", "10" or "11" PMDAC bit 0 1 0 1 LOOP bit Status x Power-down x Playback x Recording 0 Recording & Playback 1 Recording Monitor Playback Table 27. ALC Setting (x: Don't care) ALC Power-down Playback path Recording path Recording path Recording path
Default
1.
ALC Limiter Operation
During the ALC limiter operation, when either Lch or Rch exceeds the ALC limiter detection level (Table 28), the IVL and IVR values (same value) are attenuated automatically by the amount defined by the ALC limiter ATT step (Table 29). The IVL and IVR are then set to the same value for both channels. When ZELMN bit = "0" (zero cross detection is enabled), the IVL and IVR values are changed by ALC limiter operation at the individual zero crossing points of Lch and Rch or at the zero crossing timeout. ZTM1-0 bits set the zero crossing timeout period of both ALC limiter and recovery operation (Table 30). When ZELMN bit = "1" (zero cross detection is disabled), IVL and IVR values are immediately (period: 1/fs) changed by ALC limiter operation. Attenuation step is fixed to 1 step regardless as the setting of LMAT1-0 bits. The attenuation operation is done continuously until the input signal level becomes ALC limiter detection level (Table 28) or less. After completing the attenuation operation, unless ALC bit is changed to "0", the operation repeats when the input signal level exceeds LMTH1-0 bits. LMTH1 0 0 1 1 LMTH0 ALC Limier Detection Level ALC Recovery Waiting Counter Reset Level 0 ALC Output -2.5dBFS -2.5dBFS > ALC Output -4.1dBFS 1 ALC Output -4.1dBFS -4.1dBFS > ALC Output -6.0dBFS 0 ALC Output -6.0dBFS -6.0dBFS > ALC Output -8.5dBFS 1 ALC Output -8.5dBFS -8.5dBFS > ALC Output -12dBFS Table 28. ALC Limiter Detection Level / Recovery Counter Reset Level ZELMN 0 1 LMAT1 LMAT0 ALC Limiter ATT Step 0 0 1 step 0.375dB 0 1 2 step 0.750dB 1 0 4 step 1.500dB 1 1 8 step 3.000dB x x 1step 0.375dB Table 29. ALC Limiter ATT Step (x: Don't care)
Default
Default
ZTM1 0 0 1 1
ZTM0 0 1 0 1
Zero Crossing Timeout Period 8kHz 16kHz 44.1kHz 128/fs 16ms 8ms 2.9ms 256/fs 32ms 16ms 5.8ms 512/fs 64ms 32ms 11.6ms 1024/fs 128ms 64ms 23.2ms Table 30. ALC Zero Crossing Timeout Period
Default
MS0605-E-00 - 43 -
2007/06
[AK4645EZ]
2.
ALC Recovery Operation
The ALC recovery operation waits for the WTM2-0 bits (Table 31) to be set after completing the ALC limiter operation. If the input signal does not exceed "ALC recovery waiting counter reset level" (Table 28) during the wait time, the ALC recovery operation is done. The IVL and IVR values are automatically incremented by RGAIN1-0 bits (Table 32) up to the set reference level (Table 33) with zero crossing detection which timeout period is set by ZTM1-0 bits (Table 30). Then the IVL and IVR are set to the same value for both channels. The ALC recovery operation is done at a period set by WTM2-0 bits. When zero cross is detected at both channels during the wait period set by WTM2-0 bits, the ALC recovery operation waits until WTM2-0 period and the next recovery operation is done. If ZTM1-0 is longer than WTM2-0 and no zero crossing occurs, the ALC recovery operation is done at a period set by ZTM1-0 bits. For example, when the current IVOL value is 30H and RGAIN1-0 bits are set to "01", IVOL is changed to 32H by the auto limiter operation and then the input signal level is gained by 0.75dB (=0.375dB x 2). When the IVOL value exceeds the reference level (REF7-0), the IVOL values are not increased. When "ALC recovery waiting counter reset level (LMTH1-0) Output Signal < ALC limiter detection level (LMTH1-0)" during the ALC recovery operation, the waiting timer of ALC recovery operation is reset. When "ALC recovery waiting counter reset level (LMTH1-0) > Output Signal", the waiting timer of ALC recovery operation starts. The ALC operation corresponds to the impulse noise. When the impulse noise is input, the ALC recovery operation becomes faster than a normal recovery operation (Fast Recovery Operation). When large noise is input to microphone instantaneously, the quality of small level in the large noise can be improved by this fast recovery operation. The speed of fast recovery operation is set by RFST1-0 bits (Table 34). WTM2 0 0 0 0 1 1 1 1 WTM1 0 0 1 1 0 0 1 1 WTM0 ALC Recovery Operation Waiting Period 8kHz 16kHz 44.1kHz 0 128/fs 16ms 8ms 2.9ms 1 256/fs 32ms 16ms 5.8ms 0 512/fs 64ms 32ms 11.6ms 1 1024/fs 128ms 64ms 23.2ms 0 2048/fs 256ms 128ms 46.4ms 1 4096/fs 512ms 256ms 92.9ms 0 8192/fs 1024ms 512ms 185.8ms 1 16384/fs 2048ms 1024ms 371.5ms Table 31. ALC Recovery Operation Waiting Period RGAIN0 GAIN STEP 0 1 step 0.375dB 1 2 step 0.750dB 0 3 step 1.125dB 1 4 step 1.500dB Table 32. ALC Recovery GAIN Step
Default
RGAIN1 0 0 1 1
Default
MS0605-E-00 - 44 -
2007/06
[AK4645EZ]
REF7-0 GAIN(dB) Step F1H +36.0 F0H +35.625 EFH +35.25 : : E2H +30.375 0.375dB E1H +30.0 Default E0H +29.625 : : 03H -53.25 02H -53.625 01H -54.0 00H MUTE Table 33. Reference Level at ALC Recovery operation RFST1 bit 0 0 1 1 RFST0 bit Recovery Speed 0 4 times 1 8 times 0 16times 1 N/A Table 34. Fast Recovery Speed Setting
Default
MS0605-E-00 - 45 -
2007/06
[AK4645EZ]
3.
Example of ALC Operation
Table 35 shows the examples of the ALC setting for mic recording. Register Name LMTH1-0 ZELMN ZTM1-0 WTM2-0 REF7-0 IVL7-0, IVR7-0 LMAT1-0 RGAIN1-0 RFST1-0 ALC Comment Limiter detection Level Limiter zero crossing detection Zero crossing timeout period Recovery waiting period *WTM2-0 bits should be the same or longer data as ZTM1-0 bits. Maximum gain at recovery operation Gain of IVOL Limiter ATT step Recovery GAIN step Fast Recovery Speed ALC enable fs=8kHz Operation -4.1dBFS Enable 32ms 32ms +30dB +30dB fs=44.1kHz Operation -4.1dBFS Enable 23.2ms 23.2ms +30dB +30dB 1 step 1 step 4 times Enable
Data 01 0 01 001 E1H E1H
Data 01 0 11 011 E1H E1H 00 00 00 1
00 1 step 00 1 step 00 4 times 1 Enable Table 35. Example of the ALC setting
The following registers should not be changed during the ALC operation. These bits should be changed after the ALC operation is finished by ALC bit = "0" or PMADL=PMADR bits = "0". * LMTH1-0, LMAT1-0, WTM2-0, ZTM1-0, RGAIN1-0, REF7-0, ZELMN, RFST1-0
Example: Limiter = Zero crossing Enable Recovery Cycle = 32ms@8kHz Zero Crossing Timeout Period = 32ms@8kHz Limiter and Recovery Step = 1 Fast Recovery Speed = 4 step Gain of IVOL = +30dB Maximum Gain = +30.0dB Limiter Detection Level = -4.1dBFS ALC bit = "1" (1) Addr=06H, Data=14H
Manual Mode
WR (ZTM1-0, WTM2-0, RFST1-0)
WR (REF7-0)
(2) Addr=08H, Data=E1H
WR (IVL/R7-0)
* The value of IVOL should be the same or smaller than REF's
(3) Addr=09H&0CH, Data=E1H
WR (RGAIN1, LMTH1)
(4) Addr=0BH, Data=00H
WR (LMAT1-0, RGAIN0, ZELMN, LMTH0; ALC= "1")
(5) Addr=07H, Data=21H
ALC Operation
Note : WR : Write Figure 36. Registers set-up sequence at ALC operation
MS0605-E-00 - 46 -
2007/06
[AK4645EZ]
Input Digital Volume (Manual Mode)
The input digital volume becomes a manual mode when ALC bit is "0". This mode is used in the case shown below. 1. 2. 3. After exiting reset state, set-up the registers for the ALC operation (ZTM1-0, LMTH1-0 and etc) When the registers for the ALC operation (Limiter period, Recovery period and etc) are changed. For example; when the change of the sampling frequency. When IVOL is used as a manual volume.
IVL7-0 and IVR7-0 bits set the gain of the volume control (Table 36). The IVOL value is changed at zero crossing or timeout. Zero crossing timeout period is set by ZTM1-0 bits. If IVL7-0 or IVR7-0 bits are written during PMADL=PMADR bits = "0", IVOL operation starts with the written values at the end of the ADC initialization cycle after PMADL or PMADR bit is changed to "1". Even if the path is switched from recording to playback, the register setting of IVOL remains. Therefore, IVL7-0 and IVR7-0 bits should be set to "91H" (0dB). IVL7-0 IVR7-0 F1H F0H EFH : E2H E1H E0H : 03H 02H 01H 00H GAIN (dB) Step
+36.0 +35.625 +35.25 : +30.375 0.375dB +30.0 +29.625 : -53.25 -53.625 -54 MUTE Table 36. Input Digital Volume Setting
Default
MS0605-E-00 - 47 -
2007/06
[AK4645EZ]
When writing to the IVL7-0 and IVR7-0 bits continuouslly, the control register should be written by an interval more than zero crossing timeout. If not, IVL and IVR are not changed since zero crossing counter is reset at every write operation. If the same register value as the previous write operation is written to IVL and IVR, this write operation is ignored and zero crossing counter is not reset. Therefore, IVL and IVR can be written by an interval less than zero crossing timeout.
ALC bit
ALC Status
Disable
Enable
Disable
IVL7-0 bits
E1H(+30dB)
IVR7-0 bits
C6H(+20dB)
Internal IVL
E1H(+30dB) (1)
E1(+30dB) --> F1(+36dB)
E1(+30dB) (2)
Internal IVR
C6H(+20dB)
E1(+30dB) --> F1(+36dB)
C6H(+20dB)
Figure 37. IVOL value during ALC operation (1) The IVL value becomes the start value if the IVL and IVR are different when the ALC starts. The wait time from ALC bit = "1" to ALC operation start by IVL7-0 bits is at most recovery time (WTM2-0 bits) plus zerocross timeout period (ZTM1-0 bits). (2) Writing to IVL and IVR registers (09H and 0CH) is ignored during ALC operation. After ALC is disabled, the IVOL changes to the last written data by zero crossing or timeout. When ALC is enabled again, ALC bit should be set to "1" by an interval more than zero crossing timeout period after ALC bit = "0".
MS0605-E-00 - 48 -
2007/06
[AK4645EZ]
De-emphasis Filter
The AK4645 includes the digital de-emphasis filter (tc = 50/15s) by IIR filter. Setting the DEM1-0 bits enables the de-emphasis filter (Table 37). DEM1 0 0 1 1 DEM0 Mode 0 44.1kHz 1 OFF Default 0 48kHz 1 32kHz Table 37. De-emphasis Control
Bass Boost Function
The BST1-0 bits control the amount of low frequency boost applied to the DAC output signal (Table 38). If the BST1-0 bits are set to "01" (MIN Level), use a 47F capacitor for AC-coupling. If the boosted signal exceeds full scale, the analog output clips to the full scale. Figure 38 shows the boost frequency response at -20dB signal input.
Boost Filter (fs=44.1kHz) 0 MAX -5 Level [dB] MID -10 MIN -15 -20 -25 10 100 Frequency [Hz]
Figure 38. Bass Boost Frequency Response (fs=44.1kHz) BST1 0 0 1 1 BST0 Mode 0 OFF 1 MIN 0 MID 1 MAX Table 38. Bass Boost Control
1000
10000
Default
MS0605-E-00 - 49 -
2007/06
[AK4645EZ]
Digital Output Volume
The AK4645 has a digital output volume (256 levels, 0.5dB step, Mute). The volume can be set by the DVL7-0 and DVR7-0 bits. The volume is included in front of a DAC block. The input data of DAC is changed from +12 to -115dB or MUTE. When the DVOLC bit = "1", the DVL7-0 bits control both Lch and Rch attenuation levels. When the DVOLC bit = "0", the DVL7-0 bits control Lch level and DVR7-0 bits control Rch level. This volume has a soft transition function. The DVTM bit sets the transition time between set values of DVL/R7-0 bits as either 1061/fs or 256/fs (Table 40). When DVTM bit = "0", a soft transition between the set values occurs (1062 levels). It takes 1061/fs (=24ms@fs=44.1kHz) from 00H (+12dB) to FFH (MUTE). DVL/R7-0 00H 01H 02H : 18H : FDH FEH FFH Gain Step +12.0dB +11.5dB +11.0dB : 0.5dB 0dB : -114.5dB -115.0dB MUTE (-) Table 39. Digital Volume Code Table
Default
DVTM bit 0 1
Transition time between DVL/R7-0 bits = 00H and FFH Setting fs=8kHz fs=44.1kHz 1061/fs 133ms 24ms 256/fs 32ms 6ms Table 40. Transition Time Setting of Digital Output Volume
Default
MS0605-E-00 - 50 -
2007/06
[AK4645EZ]
Soft Mute
Soft mute operation is performed in the digital domain. When the SMUTE bit goes to "1", the output signal is attenuated by - ("0") during the cycle set by the DVTM bit. When the SMUTE bit is returned to "0", the mute is cancelled and the output attenuation gradually changes to the value set by the DVL/R7-0 bits during the cycle set of the DVTM bit. If the soft mute is cancelled within the cycle set by the DVTM bit after starting the operation, the attenuation is discontinued and returned to the value set by the DVL/R7-0 bits. The soft mute is effective for changing the signal source without stopping the signal transmission (Figure 39).
S M U T E bit
D VTM bit D VL/R 7-0 bits D VTM bit
(1) (3)
A ttenuation
-
GD (2) A nalog O utput GD
Figure 39. Soft Mute Function (1) The output signal is attenuated until - ("0") by the cycle set by the DVTM bit. (2) Analog output corresponding to digital input has the group delay (GD). (3) If the soft mute is cancelled within the cycle set by the DVTM bit, the attenuation is discounted and returned to the value set by the DVL/R7-0 bits.
MS0605-E-00 - 51 -
2007/06
[AK4645EZ]
Analog Mixing: Stereo Input (LIN2/RIN2/LIN4/RIN4, AIN3 bit = "1": LIN3/RIN3 pins)
When PMAINL2=PMAINR2 bits = "1", LIN2 and RIN2 pins can be used as stereo line input for analog mixing. When the LINH2 and RINH2 bits are set to "1", the input signal from the LIN2/RIN2 pins is output to Headphone-Amp. When the LINL2/RINR2 bits are set to "1", the input signal from the LIN2/RIN2 pins is output to the stereo line output amplifier. When PMAINL4=PMAINR4 bits = "1", LIN4 and RIN4 pins can be used as stereo line input for analog mixing. When the LINH4 and RINH4 bits are set to "1", the input signal from the LIN4/RIN4 pins is output to Headphone-Amp. When the LINL4/RINR4 bits are set to "1", the input signal from the LIN4/RIN4 pins is output to the stereo line output amplifier. When the analog mixing is used, A/D converter is also available if PMADL or PMADR bit is "1". In this case, the input resistance of LIN2/RIN2/LIN4/RIN4 pins becomes 30k (typ) at MGAIN1-0 bits = "00" and 20k (typ) at MGAIN1-0 bits = "01", "10" or "11", respectively. When AIN3 bit = "1", MIN and VCOC pins becomes LIN3 and RIN3 pins, respectively. In this case, PLL is not available. When PMAINL3=PMAINR3 bits = "1", LIN3 and RIN3 pins can be used as stereo line input for analog mixing. When PMMICL=PMMICR=MICL3=MICR3 bits = "1", analog mixing source is changed from LIN3/RIN3 iput to MIC-Amp output signal. When the LINH3 and RINH3 bits are set to "1", the input signal from the LIN3/RIN3 pins is output to Headphone-Amp. When the LINL3/RINR3 bits are set to "1", the input signal from the LIN3/RIN3 pins is output to the stereo line output amplifier. When the analog mixing is used, A/D converter is also available if PMADL or PMADR bit is "1". When the analog mixing is used at MICL3=MICR3 bits = "0", the input resistance of LIN3/RIN3 pins becomes 30k (typ) at MGAIN1-0 bits = "00" and 20k (typ) at MGAIN1-0 bits = "01", "10" or "11", respectively. When the analog mixing is used at MICL3=MICR3 bits = "1", the input resistance of LIN3/RIN3 pins becomes 60k (typ) at MGAIN1-0 bits = "00" and 30k (typ) at MGAIN1-0 bits = "01", "10" or "11", respectively. Table 41, Table 42 and Table 43 show the typical gain.
AK4645
INL1-0 bits LIN1/IN1- pin ADC Lch
RIN1/IN1+ pin MDIF1 bit MIC-Amp
INR1-0 bits RIN2/IN2- pin LIN2/IN2+ pin MDIF2 bit MIN/LIN3 pin VCOC/RIN3 pin MICR3 bit PMAINR3 bit MICL3 bit MIC-Amp These blocks are not available at PLL mode. ADC Rch
LIN4/IN4+ pin RIN4/IN4- pin PMAINR4 bit PMAINR2 bit PMAINL4 bit PMAINL2 bit
Lineout, HP-Amp
Figure 40. Analog Mixing Circuit (Stereo Input) MS0605-E-00 - 52 2007/06
PMAINL3 bit
[AK4645EZ]
PMAINL2 bit PMAINR2 bit LINL2/RINR2 LIN2/RIN2 LINH2/RINH2 HPL, HPR pins LOUT/LOP pin, ROUT/LON pin
Figure 41. Analog Mixing Circuit (LIN2/RIN2)
PMAINL4 bit PMAINR4 bit LINL4/RINR4 LIN4/RIN4 LINH4/RINH4 HPL, HPR pins LOUT/LOP pin, ROUT/LON pin
Figure 42. Analog Mixing Circuit (LIN4/RIN4)
PMAINL3 bit PMAINR3 bit LINL3/RINR3 LIN3/RIN3 LINH3/RINH3 HPL, HPR pins LOUT/LOP pin, ROUT/LON pin
Figure 43. Analog Mixing Circuit (LIN3/RIN3: PLL is not available.) LIN2/RIN2/LIN3/RIN3/LIN4/RIN4 LOUT/ROUT 0 0dB Default 1 +2dB Table 41. LIN2/RIN2/LIN3/RIN3/LIN4/RIN4 Input LOUT/ROUT Output Gain (typ) LIN2/RIN2/LIN3/RIN3/LIN4/RIN4 LOP/LON 0 0dB Default 1 +2dB Table 42. LIN2/RIN2/LIN3/RIN3/LIN4/RIN4 Input LOP/LON Output Gain (typ) LIN2/RIN2/LIN3/RIN3/LIN4/RIN4 HPL/HPR 0 0dB Default 1 +3.6dB Table 43. LIN2/RIN2/LIN3/RIN3/LIN4/RIN4 Input Headphone-Amp Output Gain (typ) HPG bit LOVL bit LOVL bit
MS0605-E-00 - 53 -
2007/06
[AK4645EZ]
Analog Mixing: Full-differentical Mono Input (L4DIF bit = "1": IN4+/IN4- pins)
When L4DIF bit = "1", LIN4 and RIN4 pins becomes IN4+ and IN4- pins, respectively. When PMAINL4 bit = "1", IN4+ and IN4- pins can be used as full-differentinal mono line input for analog mixing. When the LINH4 and RINH4 bits are set to "1", the input signal from the IN4+/IN4- pins is output to Headphone-Amp. When the LINL4/RINR4 bits are set to "1", the input signal from the IN4+/IN4- pins is output to the stereo line output amplifier. Table 44, Table 45 and Table 46 show the typical gain. Input signal amplitude is defined as (IN4+) - (IN4-).
AK4645
MIC-Amp Lch LIN4/IN4+ pin
L4DIF bit PMAINL4 bit
MIC-Amp Rch RIN4/IN4- pin
PMAINR4 bit
Lineout, HP-Amp
Figure 44. Full-differential Mono Analog Mixing Circuit LOVL bit IN4+/IN4- LOUT/ROUT 0 Default -6dB 1 -4dB Table 44. IN4+/IN4- Input LOUT/ROUT Output Gain (typ) LOVL bit IN4+/IN4- LOP/LON 0 0dB Default 1 +2dB Table 45. IN4+/IN4- Input LOP/LON Output Gain (typ) HPG bit IN4+/IN4- HPL/HPR 0 Default -6dB 1 -2.4dB Table 46. IN4+/IN4- Input Headphone-Amp Output Gain (typ)
MS0605-E-00 - 54 -
2007/06
[AK4645EZ]
Analog Mixing: Mono Input (AIN3 bit = "0": MIN pin)
When AIN3 bit = "0", MIN pin is used as mono input for analog mixing. When the PMMIN bit is set to "1", the mono input is powered-up. When the MINH bit is set to "1", the input signal from the MIN pin is output to Headphone-Amp. When the MINL bit is set to "1", the input signal from the MIN pin is output to the stereo line output amplifier. The external resister Ri adjusts the signal level of MIN input. Table 47, Table 48 and Table 49 show the typical gain example at Ri = 20k. This gain is in inverse proportion to Ri .
Ri MIN
MINL LOUT/LOP pin, ROUT/LON pin
MINH HPL, HPR pin
Figure 7. Block Diagram of MIN pin
LOVL bit 0 1 Table 47. MIN Input LOVL bit 0 1 Table 48. MIN Input HPG bit 0 1 Table 49. MIN Input
LOUT/ROUT 0dB Default +2dB LOUT/ROUT Output Gain (typ) at Ri = 20k LOP/LON +6dB Default +8dB LOP/LON Output Gain (typ) at Ri = 20k HPL/HPR Default -20dB -16.4dB Headphone-Amp Output Gain (typ) at Ri = 20k MIN MIN
MIN
MS0605-E-00 - 55 -
2007/06
[AK4645EZ]
Stereo Line Output (LOUT/ROUT pins)
When DACL bit is "1", Lch/Rch signal of DAC is output from the LOUT/ROUT pins which is single-ended. When DACL bit is "0", output signal is muted and LOUT/ROUT pins output VCOM voltage. The load impedance is 10k (min.). When the PMLO=LOPS bits = "0", the stereo line output enters power-down mode and the output is pulled-down to AVSS by 100k(typ). When the LOPS bit is "1", stereo line output enters power-save mode. Pop noise at power-up/down can be reduced by changing PMLO bit at LOPS bit = "1". In this case, output signal line should be pulled-down to AVSS by 20k after AC coupled as Figure 46. Rise/Fall time is 300ms(max) at C=1F and AVDD=3.3V. When PMLO bit = "1" and LOPS bit = "0", stereo line output is in normal operation. LOVL bit set the gain of stereo line output. When LOM bit = "1", DAC output signal is output to LOUT and ROUT pins as (L+R)/2 mono signal. When LOM3 bit = "1", the signal selected by MICL3 and MICR3 bits (LIN3/RIN3 inputs or MIC-Amp outputs) to LOUT and ROUT pins as (L+R)/2 mono signal.
"DACL"
"LOVL" LOUT pin
DAC ROUT pin
Figure 45. Stereo Line Output LOPS 0 1 PMLO Mode LOUT/ROUT pin 0 Power-down Pull-down to AVSS 1 Normal Operation Normal Operation 0 Power-save Fall down to AVSS 1 Power-save Rise up to VCOM Table 50. Stereo Line Output Mode Select (x: Don't care) LOVL Gain Output Voltage (typ) 0 0dB 0.6 x AVDD Default 1 +2dB 0.757 x AVDD Table 51. Stereo Line Output Volume Setting
Default
LOUT ROUT
1F
220
20k
Figure 46. External Circuit for Stereo Line Output (in case of using Pop Reduction Circuit)
MS0605-E-00 - 56 -
2007/06
[AK4645EZ]

(2 ) P M L O b it (1 ) L O P S b it (3 ) (4 ) (6 ) (5 )
L O U T , R O U T p in s 300 m s
N o r m a l O u tp u t 300 m s
Figure 47. Stereo Line Output Control Sequence (in case of using Pop Reduction Circuit) (1) Set LOPS bit = "1". Stereo line output enters the power-save mode. (2) Set PMLO bit = "1". Stereo line output exits the power-down mode. LOUT and ROUT pins rise up to VCOM voltage. Rise time is 200ms (max 300ms) at C=1F and AVDD=3.3V. (3) Set LOPS bit = "0" after LOUT and ROUT pins rise up. Stereo line output exits the power-save mode. Stereo line output is enabled. (4) Set LOPS bit = "1". Stereo line output enters power-save mode. (5) Set PMLO bit = "0". Stereo line output enters power-down mode. LOUT and ROUT pins fall down to AVSS. Fall time is 200ms (max 300ms) at C=1F and AVDD=3.3V. (6) Set LOPS bit = "0" after LOUT and ROUT pins fall down. Stereo line output exits the power-save mode.
MS0605-E-00 - 57 -
2007/06
[AK4645EZ]

When AIN3 bit = "0", DACL, MINL, LINL2, RINR2, LINL4 and RINR4 bits controls each path switch. MIN path mixing gain is 0dB(typ)@LOVL bit = "0" when the external input resistance is 20k. LIN2, RIN2, LIN4, RIN4 and DAC pathes mixing gain is 0dB(typ)@LOVL bit = "0".
LINL2 bit LIN2 pin 0dB LINL4 bit LIN4 pin 0dB MINL bit MIN pin 0dB DACL bit DAC Lch 0dB M I X LOUT pin
Figure 48. LOUT Mixing Circuit (AIN3 bit = "0", LOVL bit = "0")
RINR2 bit RIN2 pin 0dB RINR4 bit RIN4 pin 0dB MINL bit MIN pin 0dB DACL bit DAC Rch 0dB M I X ROUT pin
Figure 49. ROUT Mixing Circuit (AIN3 bit = "0", LOVL bit = "0")
MS0605-E-00 - 58 -
2007/06
[AK4645EZ]
When AIN3 bit = "1", DACL, LINL2, RINR2, LINL3, RINR3, LINL4, RINR4, MICL3 and MICR3 bits controls each path switch. All pathes mixing gain is 0dB(typ)@LOVL bit = "0".
LINL2 bit LIN2 pin 0dB LINL4 bit LIN4 pin MICL3 bit LIN3 pin 0dB *These blocks are not available at PLL mode. DACL bit DAC Lch 0dB 0dB LINL3 bit M I X LOUT pin
LIN1 pin
MIC-Amp Lch
Figure 50. LOUT Mixing Circuit (AIN3 bit = "1", LOVL bit = "0")
RINR2 bit RIN2 pin 0dB RINR4 bit RIN4 pin MICR3 bit RIN3 pin 0dB *These blocks are not available at PLL mode. DACL bit DAC Rch 0dB 0dB RINR3 bit M I X ROUT pin
RIN1 pin
MIC-Amp Rch
Figure 51. ROUT Mixing Circuit (AIN3 bit = "1", LOVL bit = "0")
MS0605-E-00 - 59 -
2007/06
[AK4645EZ]
Full-differential Mono Line Output (LOP/LON pins)
When LODIF bit = "1", LOUT/ROUT pins become LOP/LON pins, respectively. Lch/Rch signal of DAC or LIN2/RIN2/LIN3/RIN3/LIN4/RIN4 is output from the LOP/LON pins which is full-differential as (L+R)/2 signal. The load impedance is 10k (min) for LOP and LON pins, respectively. When the PMLO bit = "0", the mono line output enters power-down mode and the output is Hi-Z. When the PMLO bit is "1" and LOPS bit is "1", mono line output enters power-save mode. Pop noise at power-up/down can be reduced by changing PMLO bit at LOPS bit = "0". When PMLO bit = "1" and LOPS bit = "0", mono line output enters in normal operation. LOVL bit set the gain of mono line output. When L4DIF=LODIF bits = "1", full-differential output signal is as follows: (LOP) - (LON) = (IN4+) - (IN4-).
"DACL" "LOVL" LOP pin DAC LON pin
Figure 52. Mono Line Output PMLO 0 1 LOPS Mode LOP LON x Power-down Hi-Z Hi-Z 1 Power-save Hi-Z VCOM/2 0 Normal Operation Normal Operation Normal Operation Table 52. Mono Line Output Mode Setting (x: Don't care) LOVL 0 1 Gain Output Voltage (typ) +6dB 1.2 x AVDD Default +8dB 1.5 x AVDD Table 53. Mono Line Output Volume Setting
Default
PMLO bit
LOPS bit
LOP pin
Hi-Z
Hi-Z
LON pin
Hi-Z
VCOM
VCOM
Hi-Z
Figure 53. Power-up/Power-down Timing for Mono Line Output
MS0605-E-00 - 60 -
2007/06
[AK4645EZ]

When AIN3 bit = "0", DACL, MINL, LINL2, RINR2, LINL4 and RINR4 bits controls each path switch. MIN path mixing gain is +6dB(typ)@LOVL bit = "0" when the external input resistance is 20k. LIN2, RIN2, LIN4, RIN4 and DAC pathes mixing gain is 0dB(typ)@LOVL bit = "0".
LINL2 bit LIN2 pin 0dB RINR2 bit RIN2 pin 0dB LINL4 bit LIN4 pin 0dB RINR4 bit RIN4 pin 0dB X MINL bit MIN pin +6dB DACL bit DAC Lch 0dB DACL bit DAC Rch 0dB M I LOP/N pin
Figure 54. Mono Line Output Mixing Circuit (AIN3 bit = "0", LOVL bit = "0") When AIN3 bit = "1", DACL, LINL2, RINR2, LINL3, RINR3, LINL4, RINR4, MICL3 and MICR3 bits controls each path switch. All pathes mixing gain is 0dB(typ)@LOVL bit = "0".
LINL2 bit LIN2 pin 0dB LINL4 bit LIN4 pin MICL3 bit LIN3 pin 0dB *These blocks are not available at PLL mode. RINR2 bit RIN2 pin 0dB RINR4 bit RIN4 pin MICR3 bit RIN3 pin 0dB *These blocks are not available at PLL mode. DACL bit DAC Lch 0dB DACL bit DAC Rch 0dB 0dB RINR3 bit M I X LOP/N pin 0dB LINL3 bit
LIN1 pin
MIC-Amp Lch
RIN1 pin
MIC-Amp Rch
Figure 55. Mono Line Output Mixing Circuit (AIN3 bit = "1", LOVL bit = "0")
MS0605-E-00 - 61 -
2007/06
[AK4645EZ]
Headphone Output
Power supply voltage for the Headphone-Amp is supplied from the HVDD pin and centered on the HVDD/2 voltage at VBAT bit = "0". The load resistance is 16 (min). HPG bit selects the output voltage (Table 54). When HPM bit = "1", DAC output signal is output to HPL and HPR pins as (L+R)/2 mono signal. When HPM3 bit = "1", the signal selected by MICL3 and MICR3 bits (LIN3/RIN3 inputs or MIC-Amp outputs) to HPL and HPR pins as (L+R)/2 mono signal. HPG bit 0 1 Output Voltage [Vpp] 0.6 x AVDD 0.91 x AVDD Table 54. Headphone-Amp Output Voltage When the HPMTN bit is "0", the common voltage of Headphone-Amp falls and the outputs (HPL and HPR pins) go to "L" (HVSS). When the HPMTN bit is "1", the common voltage rises to HVDD/2 at VBAT bit = "0". A capacitor between the MUTET pin and ground reduces pop noise at power-up. Rise/Fall time constant is in proportional to HVDD voltage and the capacitor at MUTET pin. [Example]: A capacitor between the MUTET pin and ground = 1.0F, HVDD=3.3V: Rise/fall time constant: = 100ms(typ), 250ms(max) Time until the common goes to HVSS when HPMTN bit = "1" "0": 500ms(max) When PMHPL and PMHPR bits are "0", the Headphone-Amp is powered-down, and the outputs (HPL and HPR pins) go to "L" (HVSS).
PMHPL bit, PMHPR bit
HPMTN bit HPL pin, HPR pin
(1) (2)
(3)
(4)
Figure 56. Power-up/Power-down Timing for Headphone-Amp (1) Headphone-Amp power-up (PMHPL, PMHPR bit = "1"). The outputs are still HVSS. (2) Headphone-Amp common voltage rises up (HPMTN bit = "1"). Common voltage of Headphone-Amp is rising. (3) Headphone-Amp common voltage falls down (HPMTN bit = "0"). Common voltage of Headphone-Amp is falling. (4) Headphone-Amp power-down (PMHPL, PMHPR bit = "0"). The outputs are HVSS. If the power supply is switched off or Headphone-Amp is powered-down before the common voltage goes to HVSS, some POP noise occurs.

When BOOST=OFF, the cut-off frequency (fc) of Headphone-Amp depends on the external resistor and capacitor. This fc can be shifted to lower frequency by using bass boost function. Table 55 shows the cut off frequency and the output power for various resistor/capacitor combinations. The headphone impedance RL is 16. Output powers are shown at HVDD = 3.0, 3.3 and 5.0V. The output voltage of headphone is 0.6 x AVDD (Vpp) @HPG bit = "0" and 0.91 x AVDD (Vpp) @HPG bit = "1". When an external resistor R is smaller than 12, put an oscillation prevention circuit (0.22F20% capacitor and 1020% resistor) because it has the possibility that Headphone-Amp oscillates.
MS0605-E-00 - 62 -
2007/06
[AK4645EZ]
HP-AMP
C
R
Headphone 16
AK4645
0.22 10
Figure 57. External Circuit Example of Headphone Output Power [mW]@0dBFS fc [Hz] BOOST HVDD=3.0V HVDD=3.3V HVDD=5V =MIN AVDD=3.0V AVDD=3.3V AVDD=3.3V @fs=44.1kHz 45 17 25.3 30.6 30.6 100 43 70 28 12.5 15.1 15.1 149 78 50 19 6.3 7.7 7.7 106 47 62 51 45 17 70 (Note 42) (Note 42) 100 43 62 25 1.1 1.3 1.3 137 69 Table 55. External Circuit Example Note 41. Output power at 16 load. Note 42. Output signal is clipped. fc [Hz] BOOST =OFF
HPG bit
R []
C [F] 220 100 100 47 100 47 220 100 22 10
0 0 6.8 16 0 1 100

When HVDD is directly supplied from the battery in the mobile phone system, RF noise may influences headphone output performance. When VBAT bit is set to "1", HP-Amp PSRR for the noise applied to HVDD is improved. In this case, HP-Amp common voltage is 0.64 x AVDD (typ). When AVDD is 3.3V, common voltage is 2.1V. Therefore, when HVDD voltage becomes lower than 4.2V, the output signal will be clipped easily. VBAT bit Common Voltage [V] 0 0.5 x HVDD Table 56. HP-Amp Common Voltage 1 0.64 x AVDD

When PMVCM=PMHPL=PMHPR bits = "0" and HPZ bit = "1", HP-Amp is powered-down and HPL/R pins are pulled-down to HVSS by 200k (typ). In this setting, it is available to connect HP-Amp of AK4645 and external single supply HP-Amp by "wired OR". In this mode, power supply current is 20A(typ). PMVCM x 0 1 1 PMHPL/R 0 0 1 1 HPMTN HPZ Mode x 0 Power-down & Mute x 1 Power-down 0 x Mute 1 x Normal Operation Table 57. HP-Amp Mode Setting (x: Don't care) HPL/R pins HVSS Pull-down by 200k HVSS Normal Operation
Default
MS0605-E-00 - 63 -
2007/06
[AK4645EZ]
HPL pin
AK4645
Headphone HPR pin
Another HP-Amp
Figure 58. Wired OR with External HP-Amp

When AIN3 bit = "0", DACH, MINH, LINH2, RINH2, LINH4 and RINH4 bits controls each path switch. MIN path mixing gain is -20dB(typ)@HPG bit = "0" when the external input resistance is 20k. LIN2, RIN2, LIN4, RIN4 and DAC pathes mixing gain is 0dB(typ)@HPG bit = "0".
LINH2 bit LIN2 pin 0dB LINH4 bit LIN4 pin 0dB MINH bit MIN pin
-20dB
M I X DACH bit HPL pin
DAC Lch
0dB
Figure 59. HPL Mixing Circuit (AIN3 bit = "0", HPG bit = "0")
RINH2 bit RIN2 pin 0dB RINH4 bit RIN4 pin 0dB MINH bit MIN pin
-20dB
M I X DACH bit HPR pin
DAC Rch
0dB
Figure 60. HPR Mixing Circuit (AIN3 bit = "0", HPG bit = "0")
MS0605-E-00 - 64 -
2007/06
[AK4645EZ]
When AIN3 bit = "1", DACH, LINH2, RINH2, LINH3, RINH3, LINH4, RINH4, MICL3 and MICR3 bits controls each path switch. All pathes mixing gain is 0dB(typ)@HPG bit = "0".
LINH2 bit LIN2 pin 0dB LINH4 bit LIN4 pin MICL3 bit LIN3 pin 0dB *These blocks are not available at PLL mode. DACH bit DAC Lch 0dB 0dB LINH3 bit M I X HPL pin
LIN1 pin
MIC-Amp Lch
Figure 61. HPL Mixing Circuit (AIN3 bit = "1", HPG bit = "0")
RINH2 bit RIN2 pin 0dB RINH4 bit RIN4 pin MICR3 bit RIN3 pin 0dB *These blocks are not available at PLL mode. DACH bit DAC Rch 0dB 0dB RINH3 bit M I X HPR pin
RIN1 pin
MIC-Amp Rch
Figure 62. HPR Mixing Circuit (AIN3 bit = "1", HPG bit = "0")
MS0605-E-00 - 65 -
2007/06
[AK4645EZ]
Serial Control Interface
(1) 3-wire Serial Control Mode (I2C pin = "L") Internal registers may be written by using the 3-wire P interface pins (CSN, CCLK and CDTI). The data on this interface consists of a 1-bit Chip address (Fixed to "1"), Read/Write (Fixed to "1"), Register address (MSB first, 6bits) and Control data (MSB first, 8bits). Each bit is clocked in on the rising edge ("") of CCLK. Address and data are latched on the 16th CCLK rising edge ("") after CSN falling edge(""). CSN should be set to "H" once after 16 CCLKs for each address. Clock speed of CCLK is 5MHz (max). The value of internal registers are initialized by PDN pin = "L".
CSN
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Clock, "H" or "L" C1 A5 R/W A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 "1" "1" "H" or "L"
CCLK Clock, "H" or "L" CDTI "H" or "L"
C1: R/W: A5-A0: D7-D0:
Chip Address; Fixed to "1" READ/WRITE ("1": WRITE, "0": READ); Fixed to "1" Register Address Control data
Figure 63. Serial Control I/F Timing
MS0605-E-00 - 66 -
2007/06
[AK4645EZ] (2) I2C-bus Control Mode (I2C pin = "H") The AK4645 supports the fast-mode I2C-bus (max: 400kHz). Pull-up resistors at SDA and SCL pins should be connected to (TVDD+0.3)V or less voltage. (2)-1. WRITE Operations Figure 64 shows the data transfer sequence for the I2C-bus mode. All commands are preceded by a START condition. A HIGH to LOW transition on the SDA line while SCL is HIGH indicates a START condition (Figure 70). After the START condition, a slave address is sent. This address is 7 bits long followed by the eighth bit that is a data direction bit (R/W). The most significant six bits of the slave address are fixed as "001001". The next bit is CAD0 (device address bit). This bit identifies the specific device on the bus. The hard-wired input pin (CAD0 pin) sets these device address bits (Figure 65). If the slave address matches that of the AK4645, the AK4645 generates an acknowledge and the operation is executed. The master must generate the acknowledge-related clock pulse and release the SDA line (HIGH) during the acknowledge clock pulse (Figure 71). A R/W bit value of "1" indicates that the read operation is to be executed. A "0" indicates that the write operation is to be executed. The second byte consists of the control register address of the AK4645. The format is MSB first, and those most significant 2-bits are fixed to zeros (Figure 66). The data after the second byte contains control data. The format is MSB first, 8bits (Figure 67). The AK4645 generates an acknowledge after each byte has been received. A data transfer is always terminated by a STOP condition generated by the master. A LOW to HIGH transition on the SDA line while SCL is HIGH defines a STOP condition (Figure 70). The AK4645 can perform more than one byte write operation per sequence. After receiving the third byte the AK4645 generates an acknowledge and awaits the next data. The master can transmit more than one byte instead of terminating the write cycle after the first data byte is transferred. After receiving each data packet the internal 6-bit address counter is incremented by one, and the next data is automatically taken into the next address. If the address exceeds 24H prior to generating a stop condition, the address counter will "roll over" to 00H and the previous data will be overwritten. The data on the SDA line must remain stable during the HIGH period of the clock. The HIGH or LOW state of the data line can only change when the clock signal on the SCL line is LOW (Figure 72) except for the START and STOP conditions.
S T A R T
R/W="0"
S T O P Sub Address(n) Data(n) A C K A C K Data(n+1) A C K A C K Data(n+x) A C K P
SDA
Slave S Address A C K
Figure 64. Data Transfer Sequence at the I2C-Bus Mode
0
0
1
0
0
1
CAD0
R/W
(Those CAD1/0 should match with CAD1/0 pins) Figure 65. The First Byte
0
0
A5
A4
A3
A2
A1
A0
Figure 66. The Second Byte
D7
D6
D5
D4
D3
D2
D1
D0
Figure 67. Byte Structure after the second byte
MS0605-E-00 - 67 -
2007/06
[AK4645EZ]
(2)-2. READ Operations Set the R/W bit = "1" for the READ operation of the AK4645. After transmission of data, the master can read the next address's data by generating an acknowledge instead of terminating the write cycle after receiving the first data word. After receiving each data packet the internal 6-bit address counter is incremented by one, and the next data is automatically taken into the next address. If the address exceeds 24H prior to generating a stop condition, the address counter will "roll over" to 00H and the data of 00H will be read out. The AK4645 supports two basic read operations: CURRENT ADDRESS READ and RANDOM ADDRESS READ. (2)-2-1. CURRENT ADDRESS READ The AK4645 contains an internal address counter that maintains the address of the last word accessed, incremented by one. Therefore, if the last access (either a read or write) were to address n, the next CURRENT READ operation would access data from the address n+1. After receiving the slave address with R/W bit set to "1", the AK4645 generates an acknowledge, transmits 1-byte of data to the address set by the internal address counter and increments the internal address counter by 1. If the master does not generate an acknowledge to the data but instead generates a stop condition, the AK4645 ceases transmission.
S T A R T
R/W="1"
S T O P Data(n) Data(n+1) A C K A C K Data(n+2) A C K A C K Data(n+x) A C K P
SDA
Slave S Address A C K
Figure 68. CURRENT ADDRESS READ (2)-2-2. RANDOM ADDRESS READ The random read operation allows the master to access any memory location at random. Prior to issuing the slave address with the R/W bit set to "1", the master must first perform a "dummy" write operation. The master issues a start request, a slave address (R/W bit = "0") and then the register address to read. After the register address is acknowledged, the master immediately reissues the start request and the slave address with the R/W bit set to "1". The AK4645 then generates an acknowledge, 1 byte of data and increments the internal address counter by 1. If the master does not generate an acknowledge to the data but instead generates a stop condition, the AK4645 ceases transmission.
S T A R T S T A R T Sub Address(n) A C K A C K
R/W="0"
R/W="1"
S T O P Data(n) Data(n+1) A C K A C K A C K Data(n+x) A C K P
SDA
Slave S Address
Slave S Address A C K
Figure 69. RANDOM ADDRESS READ
MS0605-E-00 - 68 -
2007/06
[AK4645EZ]
SDA
SCL S start condition P stop condition
Figure 70. START and STOP Conditions
DATA OUTPUT BY TRANSMITTER not acknowledge DATA OUTPUT BY RECEIVER acknowledge SCL FROM MASTER S clock pulse for acknowledgement
1
2
8
9
START CONDITION
Figure 71. Acknowledge on the I2C-Bus
SDA
SCL
data line stable; data valid
change of data allowed
Figure 72. Bit Transfer on the I2C-Bus
MS0605-E-00 - 69 -
2007/06
[AK4645EZ]
Register Map
Addr 00H 01H 02H 03H 04H 05H 06H 07H 08H 09H 0AH 0BH 0CH 0DH 0EH 0FH 10H 11H 12H 13H 14H 15H 16H 17H 18H 19H 1AH 1BH 1CH 1DH 1EH 1FH 20H 21H 22H 23H 24H Register Name Power Management 1 Power Management 2 Signal Select 1 Signal Select 2 Mode Control 1 Mode Control 2 Timer Select ALC Mode Control 1 ALC Mode Control 2 Lch Input Volume Control Lch Digital Volume Control ALC Mode Control 3 Rch Input Volume Control Rch Digital Volume Control Mode Control 3 Mode Control 4 Power Management 3 Digital Filter Select FIL3 Co-efficient 0 FIL3 Co-efficient 1 FIL3 Co-efficient 2 FIL3 Co-efficient 3 EQ Co-efficient 0 EQ Co-efficient 1 EQ Co-efficient 2 EQ Co-efficient 3 EQ Co-efficient 4 EQ Co-efficient 5 FIL1 Co-efficient 0 FIL1 Co-efficient 1 FIL1 Co-efficient 2 FIL1 Co-efficient 3 Power Management 4 Mode Control 5 Lineout Mixing Select HP Mixing Select Reserved D7 0 HPZ 0 LOVL PLL3 PS1 DVTM 0 REF7 D6
PMVCM
HPMTN 0 LOPS PLL2 PS0 WTM2 0 REF6
D5 PMMIN PMHPL 0
MGAIN1
PLL1 FS3 ZTM1 ALC REF5
D4 0 PMHPR DACL 0 PLL0 MSBS ZTM0 ZELMN REF4
D3 PMLO M/S 0 0 BCKO BCKP WTM1 LMAT1 REF3
D2 PMDAC 0 PMMP MINL 0 FS2 WTM0 LMAT0 REF2
D1 0 MCKO 0 0 DIF1 FS1 RFST1 RGAIN0 REF1
D0 PMADL PMPLL
MGAIN0
0 DIF0 FS0 RFST0 LMTH0 REF0
IVL7
DVL7 RGAIN1 IVR7 DVR7 0 0 INR1 GN1 F3A7 F3AS F3B7 0 EQA7 EQA15 EQB7 0 EQC7 EQC15 F1A7 F1AS F1B7 0
PMAINR4
IVL6
DVL6 LMTH1 IVR6 DVR6 LOOP 0 INL1 GN0 F3A6 0 F3B6 0 EQA6 EQA14 EQB6 0 EQC6 EQC14 F1A6 0 F1B6 0
PMAINL4
IVL5
DVL5 0 IVR5 DVR5 SMUTE 0 HPG 0 F3A5 F3A13 F3B5 F3B13 EQA5 EQA13 EQB5 EQB13 EQC5 EQC13 F1A5 F1A13 F1B5 F1B13
PMAINR3
IVL4
DVL4 0 IVR4 DVR4 DVOLC 0 MDIF2 FIL1 F3A4 F3A12 F3B4 F3B12 EQA4 EQA12 EQB4 EQB12 EQC4 EQC12 F1A4 F1A12 F1B4 F1B12
PMAINL3
IVL3
DVL3 0 IVR3 DVR3 BST1 IVOLC MDIF1 EQ F3A3 F3A11 F3B3 F3B11 EQA3 EQA11 EQB3 EQB11 EQC3 EQC11 F1A3 F1A11 F1B3 F1B11
PMAINR2
IVL2
DVL2 0 IVR2 DVR2 BST0 HPM INR0 FIL3 F3A2 F3A10 F3B2 F3B10 EQA2 EQA10 EQB2 EQB10 EQC2 EQC10 F1A2 F1A10 F1B2 F1B10
PMAINL2
IVL1
DVL1 VBAT IVR1 DVR1 DEM1 MINH INL0 0 F3A1 F3A9 F3B1 F3B9 EQA1 EQA9 EQB1 EQB9 EQC1 EQC9 F1A1 F1A9 F1B1 F1B9
PMMICR
IVL0
DVL0 0 IVR0 DVR0 DEM0 DACH PMADR 0 F3A0 F3A8 F3B0 F3B8 EQA0 EQA8 EQB0 EQB8 EQC0 EQC8 F1A0 F1A8 F1B0 F1B8
PMMICL
0 LOM 0 0
0 LOM3 HPM3 0
MICR3 RINR4 RINH4 0
MICL3 LINL4 LINH4 0
L4DIF RINR3 RINH3 0
MIX LINL3 LINH3 0
AIN3 RINR2 RINH2 0
LODIF
LINL2 LINH2 0
Note 43. PDN pin = "L" resets the registers to their default values. Note 44. Unused bits must contain a "0" value.
MS0605-E-00 - 70 -
2007/06
[AK4645EZ]
Register Definitions
Addr 00H Register Name Power Management 1 Default D7 0 0 D6 PMVCM 0 D5 PMMIN 0 D4 0 0 D3 PMLO 0 D2 PMDAC 0 D1 0 0 D0 PMADL 0
PMADL: MIC-Amp Lch and ADC Lch Power Management 0: Power-down (Default) 1: Power-up When the PMADL or PMADR bit is changed from "0" to "1", the initialization cycle (1059/fs=24ms @44.1kHz) starts. After initializing, digital data of the ADC is output. PMDAC: DAC Power Management 0: Power-down (Default) 1: Power-up PMLO: Stereo Line Out Power Management 0: Power-down (Default) 1: Power-up PMMIN: MIN Input Power Management 0: Power-down (Default) 1: Power-up PMMIN or PMAINL3 bit should be set to "1" for playback. PMVCM: VCOM Power Management 0: Power-down (Default) 1: Power-up When any blocks are powered-up, the PMVCM bit must be set to "1". PMVCM bit can be set to "0" only when all power management bits of 00H, 01H, 02H, 10H, 20H and MCKO bits are "0". Each block can be powered-down respectively by writing "0" in each bit of this address. When the PDN pin is "L", all blocks are powered-down regardless as setting of this address. In this case, register is initialized to the default value. When all power management bits are "0" in the 00H, 01H, 02H, 10H and 20H addresses and MCKO bit is "0", all blocks are powered-down. The register values remain unchanged. Power supply current is 20A(typ) in this case. For fully shut down (typ. 1A), PDN pin should be "L". When neither ADC nor DAC are used, external clocks may not be present. When ADC or DAC is used, external clocks must always be present.
MS0605-E-00 - 71 -
2007/06
[AK4645EZ]
Addr 01H
Register Name Power Management 2 Default
D7 HPZ 0
D6 HPMTN 0
D5 PMHPL 0
D4 PMHPR 0
D3 M/S 0
D2 0 0
D1 MCKO 0
D0 PMPLL 0
PMPLL: PLL Power Management 0: EXT Mode and Power-Down (Default) 1: PLL Mode and Power-up MCKO: Master Clock Output Enable 0: Disable: MCKO pin = "L" (Default) 1: Enable: Output frequency is selected by PS1-0 bits. M/S: Master / Slave Mode Select 0: Slave Mode (Default) 1: Master Mode PMHPR: Headphone-Amp Rch Power Management 0: Power-down (Default) 1: Power-up PMHPL: Headphone-Amp Lch Power Management 0: Power-down (Default) 1: Power-up HPMTN: Headphone-Amp Mute Control 0: Mute (Default) 1: Normal operation HPZ: Headphone-Amp Pull-down Control 0: Shorted to GND (Default) 1: Pulled-down by 200k (typ)
Addr 02H
Register Name Signal Select 1 Default
D7 0 0
D6 0 0
D5 0 0
D4 DACL 0
D3 0 0
D2 PMMP 0
D1 0 0
D0
MGAIN0
1
MGAIN1-0: MIC-Amp Gain Control (Table 23) MGAIN1 bit is D5 bit of 03H. PMMP: MPWR pin Power Management 0: Power-down: Hi-Z (Default) 1: Power-up DACL: Switch Control from DAC to Line Output 0: OFF (Default) 1: ON When PMLO bit is "1", DACL bit is enabled. When PMLO bit is "0", the LOUT/ROUT pins go to AVSS.
MS0605-E-00 - 72 -
2007/06
[AK4645EZ]
Addr 03H
Register Name Signal Select 2 Default
D7 LOVL 0
D6 LOPS 0
D5
MGAIN1
0
D4 0 0
D3 0 0
D2 MINL 0
D1 0 0
D0 0 0
MINL: Switch Control from MIN pin to Stereo Line Output 0: OFF (Default) 1: ON When PMLO bit is "1", MINL bit is enabled. When PMLO bit is "0", the LOUT/ROUT pins go to AVSS. MGAIN1: MIC-Amp Gain Control (Table 23) LOPS: Stereo Line Output Power-Save Mode 0: Normal Operation (Default) 1: Power-Save Mode LOVL: Stereo Line Output Gain Select (Table 51 and Table 53) 0: 0dB/+6dB (Default) 1: +2dB/+8dB
Addr 04H
Register Name Mode Control 1 Default
D7 PLL3 0
D6 PLL2 0
D5 PLL1 0
D4 PLL0 0
D3 BCKO 0
D2 0 0
D1 DIF1 1
D0 DIF0 0
DIF1-0: Audio Interface Format (Table 17) Default: "10" (Left jutified) BCKO: BICK Output Frequency Select at Master Mode (Table 11) PLL3-0: PLL Reference Clock Select (Table 5) Default: "0000" (LRCK pin)
Addr 05H
Register Name Mode Control 2 Default
D7 PS1 0
D6 PS0 0
D5 FS3 0
D4 MSBS 0
D3 BCKP 0
D2 FS2 0
D1 FS1 0
D0 FS0 0
FS3-0: Sampling Frequency Select (Table 6 and Table 7) and MCKI Frequency Select (Table 12) FS3-0 bits select sampling frequency at PLL mode and MCKI frequency at EXT mode. BCKP: BICK Polarity at DSP Mode (Table 18) "0": SDTO is output by the rising edge ("") of BICK and SDTI is latched by the falling edge (""). (Default) "1": SDTO is output by the falling edge ("") of BICK and SDTI is latched by the rising edge (""). MSBS: LRCK Polarity at DSP Mode (Table 18) "0": The rising edge ("") of LRCK is half clock of BICK before the channel change. (Default) "1": The rising edge ("") of LRCK is one clock of BICK before the channel change. PS1-0: MCKO Output Frequency Select (Table 10) Default: "00" (256fs)
MS0605-E-00 - 73 -
2007/06
[AK4645EZ]
Addr 06H
Register Name Timer Select Default
D7 DVTM 0
D6 WTM2 0
D5 ZTM1 0
D4 ZTM0 0
D3 WTM1 0
D2 WTM0 0
D1 RFST1 0
D0 RFST0 0
RFST1-0: ALC First recovery Speed (Table 34) Default: "00"(4times) WTM2-0: ALC Recovery Waiting Period (Table 31) Default: "000" (128/fs) ZTM1-0: ALC Limiter/Recovery Operation Zero Crossing Timeout Period (Table 30) Default: "00" (128/fs) DVTM: Digital Volume Transition Time Setting (Table 40) 0: 1061/fs (Default) 1: 256/fs This is the transition time between DVL/R7-0 bits = 00H and FFH.
Addr 07H
Register Name ALC Mode Control 1 Default
D7 0 0
D6 0 0
D5 ALC 0
D4 ZELMN 0
D3 LMAT1 0
D2 LMAT0 0
D1
RGAIN0
0
D0 LMTH0 0
LMTH1-0: ALC Limiter Detection Level / Recovery Counter Reset Level (Table 28) Default: "00" LMTH1 bit is D6 bit of 0BH. RGAIN1-0: ALC Recovery GAIN Step (Table 32) Default: "00" RGAIN1 bit is D7 bit of 0BH. LMAT1-0: ALC Limiter ATT Step (Table 29) Default: "00" ZELMN: Zero Crossing Detection Enable at ALC Limiter Operation 0: Enable (Default) 1: Disable ALC: ALC Enable 0: ALC Disable (Default) 1: ALC Enable
Addr 08H
Register Name ALC Mode Control 2 Default
D7 REF7 1
D6 REF6 1
D5 REF5 1
D4 REF4 0
D3 REF3 0
D2 REF2 0
D1 REF1 0
D0 REF0 1
REF7-0: Reference Value at ALC Recovery Operation. 0.375dB step, 242 Level (Table 33) Default: "E1H" (+30.0dB)
MS0605-E-00 - 74 -
2007/06
[AK4645EZ]
Addr 09H 0CH
Register Name Lch Input Volume Control Rch Input Volume Control Default
D7 IVL7 IVR7 1
D6 IVL6 IVR6 1
D5 IVL5 IVR5 1
D4 IVL4 IVR4 0
D3 IVL3 IVR3 0
D2 IVL2 IVR2 0
D1 IVL1 IVR1 0
D0 IVL0 IVR0 1
IVL7-0, IVR7-0: Input Digital Volume; 0.375dB step, 242 Level (Table 36) Default: "E1H" (+30.0dB)
Addr 0AH 0DH
Register Name Lch Digital Volume Control Rch Digital Volume Control Default
D7 DVL7 DVR7 0
D6 DVL6 DVR6 0
D5 DVL5 DVR5 0
D4 DVL4 DVR4 1
D3 DVL3 DVR3 1
D2 DVL2 DVR2 0
D1 DVL1 DVR1 0
D0 DVL0 DVR0 0
DVL7-0, DVR7-0: Output Digital Volume (Table 39) Default: "18H" (0dB)
Addr 0BH
Register Name ALC Mode Control 3 Default
D7 RGAIN1 0
D6 LMTH1 0
D5 0 0
D4 0 0
D3 0 0
D2 0 0
D1 VBAT 0
D0 0 0
VBAT: HP-Amp Common Voltage (Table 56) 0: 0.5 x HVDD (Default) 1: 0.64 x AVDD LMTH1: ALC Limiter Detection Level / Recovery Counter Reset Level (Table 28) RGAIN1: ALC Recovery GAIN Step (Table 32)
Addr 0EH
Register Name Mode Control 3 Default
D7 0 0
D6 LOOP 0
D5 SMUTE 0
D4 DVOLC 1
D3 BST1 0
D2 BST0 0
D1 DEM1 0
D0 DEM0 1
DEM1-0: De-emphasis Frequency Select (Table 37) Default: "01" (OFF) BST1-0: Bass Boost Function Select (Table 38) Default: "00" (OFF) DVOLC: Output Digital Volume Control Mode Select 0: Independent 1: Dependent (Default) When DVOLC bit = "1", DVL7-0 bits control both Lch and Rch volume level, while register values of DVL7-0 bits are not written to DVR7-0 bits. When DVOLC bit = "0", DVL7-0 bits control Lch level and DVR7-0 bits control Rch level, respectively. SMUTE: Soft Mute Control 0: Normal Operation (Default) 1: DAC outputs soft-muted LOOP: Digital Loopback Mode 0: SDTI DAC (Default) 1: SDTO DAC
MS0605-E-00 - 75 -
2007/06
[AK4645EZ]
Addr 0FH
Register Name Mode Control 4 Default
D7 0 0
D6 0 0
D5 0 0
D4 0 0
D3 IVOLC 1
D2 HPM 0
D1 MINH 0
D0 DACH 0
DACH: Switch Control from DAC to Headphone-Amp 0: OFF (Default) 1: ON MINH: Switch Control from MIN pin to Headphone-Amp 0: OFF (Default) 1: ON HPM: Headphone-Amp Mono Output Select 0: Stereo (Default) 1: Mono When the HPM bit = "1", DAC output signal is output to Lch and Rch of the Headphone-Amp as (L+R)/2. IVOLC: Input Digital Volume Control Mode Select 0: Independent 1: Dependent (Default) When IVOLC bit = "1", IVL7-0 bits control both Lch and Rch volume level, while register values of IVL7-0 bits are not written to IVR7-0 bits. When IVOLC bit = "0", IVL7-0 bits control Lch level and IVR7-0 bits control Rch level, respectively.
Addr 10H
Register Name Power Management 3 Default
D7 INR1 0
D6 INL1 0
D5 HPG 0
D4 MDIF2 0
D3 MDIF1 0
D2 INR0 0
D1 INL0 0
D0 PMADR 0
PMADR: MIC-Amp Lch and ADC Rch Power Management 0: Power-down (Default) 1: Power-up INL1-0: ADC Lch Input Source Select (Table 20) Default: 00 (LIN1 pin) INR1-0: ADC Rch Input Source Select (Table 20) Default: 00 (RIN1 pin) MDIF1: Single-ended / Full-differential Input Select 1 0: Single-ended input (LIN1/RIN1 pins: Default) 1: Full-differential input (IN1+/IN1- pins) MDIF1 bit selects the input type of pins #32 and #31. MDIF2: Single-ended / Full-differential Input Select 2 0: Single-ended input (LIN2/RIN2 pins: Default) 1: Full-differential input (IN2+/IN2- pins) MDIF2 bit selects the input type of pins #30 and #29. HPG: Headphone-Amp Gain Select (Table 54) 0: 0dB (Default) 1: +3.6dB
MS0605-E-00 - 76 -
2007/06
[AK4645EZ]
Addr 11H
Register Name Digital Filter Select Default
D7 GN1 0
D6 GN0 0
D5 0 0
D4 FIL1 0
D3 EQ 0
D2 FIL3 0
D1 0 0
D0 0 0
GN1-0: Gain Select at GAIN block (Table 26) Default: "00" FIL3: FIL3 (Stereo Separation Emphasis Filter) Coefficient Setting Enable 0: Disable (Default) 1: Enable When FIL3 bit is "1", the settings of F3A13-0 and F3B13-0 bits are enabled. When FIL3 bit is "0", FIL3 block is OFF (MUTE). EQ: EQ (Gain Compensation Filter) Coefficient Setting Enable 0: Disable (Default) 1: Enable When EQ bit is "1", the settings of EQA15-0, EQB13-0 and EQC15-0 bits are enabled. When EQ bit is "0", EQ block is through (0dB). FIL1: FIL1 (Wind-noise Reduction Filter) Coefficient Setting Enable 0: Disable (Default) 1: Enable When FIL1 bit is "1", the settings of F1A13-0 and F1B13-0 bits are enabled. When FIL1 bit is "0", FIL1 block is through (0dB).
Addr 12H 13H 14H 15H 16H 17H 18H 19H 1AH 1BH 1CH 1DH 1EH 1FH
Register Name FIL3 Co-efficient 0 FIL3 Co-efficient 1 FIL3 Co-efficient 2 FIL3 Co-efficient 3 EQ Co-efficient 0 EQ Co-efficient 1 EQ Co-efficient 2 EQ Co-efficient 3 EQ Co-efficient 4 EQ Co-efficient 5 FIL1 Co-efficient 0 FIL1 Co-efficient 1 FIL1 Co-efficient 2 FIL1 Co-efficient 3 Default
D7 F3A7 F3AS F3B7 0 EQA7 EQA15 EQB7 0 EQC7 EQC15 F1A7 F1AS F1B7 0 0
D6 F3A6 0 F3B6 0 EQA6 EQA14 EQB6 0 EQC6 EQC14 F1A6 0 F1B6 0 0
D5 F3A5 F3A13 F3B5 F3B13 EQA5 EQA13 EQB5 EQB13 EQC5 EQC13 F1A5 F1A13 F1B5 F1B13 0
D4 F3A4 F3A12 F3B4 F3B12 EQA4 EQA12 EQB4 EQB12 EQC4 EQC12 F1A4 F1A12 F1B4 F1B12 0
D3 F3A3 F3A11 F3B3 F3B11 EQA3 EQA11 EQB3 EQB11 EQC3 EQC11 F1A3 F1A11 F1B3 F1B11 0
D2 F3A2 F3A10 F3B2 F3B10 EQA2 EQA10 EQB2 EQB10 EQC2 EQC10 F1A2 F1A10 F1B2 F1B10 0
D1 F3A1 F3A9 F3B1 F3B9 EQA1 EQA9 EQB1 EQB9 EQC1 EQC9 F1A1 F1A9 F1B1 F1B9 0
D0 F3A0 F3A8 F3B0 F3B8 EQA0 EQA8 EQB0 EQB8 EQC0 EQC8 F1A0 F1A8 F1B0 F1B8 0
F3A13-0, F3B13-0: FIL3 (Stereo Separation Emphasis Filter) Coefficient (14bit x 2) Default: "0000H" F3AS: FIL3 (Stereo Separation Emphasis Filter) Select 0: HPF (Default) 1: LPF EQA15-0, EQB13-0, EQC15-C0: EQ (Gain Compensation Filter) Coefficient (14bit x 2 + 16bit x 1) Default: "0000H" F1A13-0, F1B13-B0: FIL1 (Wind-noise Reduction Filter) Coefficient (14bit x 2) Default: "0000H" F1AS: FIL1 (Wind-noise Reduction Filter) Select 0: HPF (Default) 1: LPF
MS0605-E-00 - 77 -
2007/06
[AK4645EZ]
Addr 20H
Register Name Power Management 4 Default
D7
PMAINR4
D6
PMAINL4
D5
PMAINR3
D4
PMAINL3
D3
PMAINR2
D2
PMAINL2
D1
PMMICR
D0
PMMICL
0
0
0
0
0
0
0
0
PMMICL: MIC-Amp Lch Power Management 0: Power down (Default) 1: Power up PMMICR: MIC-Amp Rch Power Management 0: Power down (Default) 1: Power up PMAINL2: LIN2 Mixing Circuit Power Management 0: Power down (Default) 1: Power up PMAINR2: RIN2 Mixing Circuit Power Management 0: Power down (Default) 1: Power up PMAINL3: LIN3 Mixing Circuit Power Management 0: Power down (Default) 1: Power up PMAINR3: RIN3 Mixing Circuit Power Management 0: Power down (Default) 1: Power up PMAINL4: LIN4 Mixing Circuit Power Management 0: Power down (Default) 1: Power up PMAINR4: RIN4 Mixing Circuit Power Management 0: Power down (Default) 1: Power up
MS0605-E-00 - 78 -
2007/06
[AK4645EZ]
Addr 21H
Register Name Mode Control 5 Default
D7 0 0
D6 0 0
D5 MICR3 0
D4 MICL3 0
D3 L4DIF 0
D2 MIX 0
D1 AIN3 0
D0
LODIF
0
LODIF: Lineout Select 0: Single-ended Stereo Line Output (LOUT/ROUT pins) (Default) 1: Full-differential Mono Line Output (LOP/LON pins) AIN3: Analog Mixing Select 0: Mono Input (MIN pin) (Default) 1: Stereo Input (LIN3/RIN3 pins): PLL is not available. MIX: Mono Recording 0: Stereo (Default) 1: Mono: (L+R)/2 L4DIF: Line Input Type Select 0: Stereo Single-ended Input: LIN4/RIN4 pins (Default) 1: Mono Full-differential Input: IN4+/- pins MICL3: Switch Control from MIC-Amp Lch to Analog Output 0: LIN3 input signal is selected. (Default) 1: MIC-Amp Lch output signal is selected. MICR3: Switch Control from MIC-Amp Rch to Analog Output 0: RIN3 input signal is selected. (Default) 1: MIC-Amp Rch output signal is selected.
MS0605-E-00 - 79 -
2007/06
[AK4645EZ]
Addr 22H
Register Name Lineout Mixing Select Default
D7 LOM 0
D6 LOM3 0
D5 RINR4 0
D4 LINL4 0
D3 RINR3 0
D2 LINL3 0
D1 RINR2 0
D0 LINL2 0
LINL2: Switch Control from LIN2 pin to Stereo Line Output (without MIC-Amp) 0: OFF (Default) 1: ON RINR2: Switch Control from RIN2 pin to Stereo Line Output (without MIC-Amp) 0: OFF (Default) 1: ON LINL3: Switch Control from LIN3 pin (or MIC-Amp Lch) to Stereo Line Output 0: OFF (Default) 1: ON RINR3: Switch Control from RIN3 pin (or MIC-Amp Lch) to Stereo Line Output 0: OFF (Default) 1: ON LINL4: Switch Control from LIN4 pin to Stereo Line Output (without MIC-Amp) 0: OFF (Default) 1: ON RINR4: Switch Control from RIN4 pin to Stereo Line Output (without MIC-Amp) 0: OFF (Default) 1: ON LOM3: Mono Mixing from MIC-Amp (or LIN3/RIN3) to Stereo Line Output 0: Stereo Mixing (Default) 1: Mono Mixing LOM: Mono Mixing from DAC to Stereo Line Output 0: Stereo Mixing (Default) 1: Mono Mixing
MS0605-E-00 - 80 -
2007/06
[AK4645EZ]
Addr 23H
Register Name HP Mixing Select Default
D7 0 0
D6 HPM3 0
D5 RINH4 0
D4 LINH4 0
D3 RINH3 0
D2 LINH3 0
D1 RINH2 0
D0 LINH2 0
LINH2: Switch Control from LIN2 pin to Headphone Output (without MIC-Amp) 0: OFF (Default) 1: ON RINH2: Switch Control from RIN2 pin to Headphone Output (without MIC-Amp) 0: OFF (Default) 1: ON LINH3: Switch Control from LIN3 pin (or MIC-Amp Lch) to Headphone Output 0: OFF (Default) 1: ON RINH3: Switch Control from RIN3 pin (or MIC-Amp Lch) to Headphone Output 0: OFF (Default) 1: ON LINH4: Switch Control from LIN4 pin to Headphone Output (without MIC-Amp) 0: OFF (Default) 1: ON RINH4: Switch Control from RIN4 pin to Headphone Output (without MIC-Amp) 0: OFF (Default) 1: ON HPM3: Mono Mixing from MIC-Amp (or LIN3/RIN3) to Headphone Output 0: Stereo Mixing (Default) 1: Mono Mixing
MS0605-E-00 - 81 -
2007/06
[AK4645EZ]
SYSTEM DESIGN
Figure 73 and Figure 74 shows the system connection diagram for the AK4645. An evaluation board [AKD4645] is available which demonstrates the optimum layout, power supply arrangements and measurement results.
Headphone
47u
6.8
6.8
47u
Power Supply 2.6 3.6V
10u
Power Supply 1.6 3.6V
10 0.22u 10 0.22u
24
MUTET 23
22
21
20
0.1u
1u
19
18
External SPK-Amp Line In 25 LIN4 26 ROUT Speaker 27 LOUT Mono In External MIC 28 MIN 29 RIN2 30 LIN2 31 LIN1 Internal MIC 32 RIN1
MCKO
HVDD
17
HVSS
HPL
MCKI
RIN4
HPR
0.1u
TVDD DVDD BICK
16 15 0.1u 14 DSP 13 12 11 10 9 P
AK4645EZ
Top View
LRCK SDTO SDTI CDTI CCLK
MPWR
VCOM
VCOC
AVDD
AVSS
2.2k 2.2k 2.2k 2.2k
1
2
3
4
5
6
7
0.1u
0.1u
2.2u
Cp Analog Ground Digital Ground
Notes: - AVSS and HVSS of the AK4645 should be distributed separately from the ground of external controllers. - All digital input pins should not be left floating. - When the AK4645 is EXT mode (PMPLL bit = "0"), a resistor and capacitor of VCOC/RIN3 pin is not needed. - When the AK4645 is PLL mode (PMPLL bit = "1"), a resistor and capacitor of VCOC/RIN3 pin should be connected as shown in Table 5. - When the AK4645 is used at master mode, LRCK and BICK pins are floating before M/S bit is changed to "1". Therefore, 100k around pull-up resistor should be connected to LRCK and BICK pins of the AK4645. - 0.1F ceramic capacitor should be attached to each supply pins. The type of other capacitors is not critical. - When DVDD is supplied from AVDD via 10 series resistor, the capacitor larger than 0.1F should not be connected between DVDD and the ground. Figure 73. Typical Connection Diagram (AIN3 bit = "0", MIC Input)
MS0605-E-00 - 82 -
Rp
8
CSN
PDN
I2C
10
2007/06
[AK4645EZ]
Headphone
47u
6.8
6.8
47u
Power Supply 2.6 3.6V
10u
Power Supply 1.6 3.6V
10 0.22u 10 0.22u
20k 20k
24
MUTET 23
22
21
20
0.1u
1u
19
18
MCKO
HVDD
17
HVSS
Line In 25 LIN4 200 Line Out 200 1u 1u 26 ROUT 27 LOUT 28 LIN3 29 RIN2 Line In 30 LIN2 31 LIN1 32 RIN1
HPL
MCKI
RIN4
HPR
0.1u
TVDD DVDD BICK
16 15 0.1u 14 DSP 13 12 11 10 9 P
AK4645EZ
Top View
LRCK SDTO SDTI CDTI CCLK
MPWR
VCOM
AVDD
AVSS
RIN3
1
2
3
4
5
6
7
0.1u
2.2u
0.1u
8
CSN
PDN
I2C
10 Analog Ground Digital Ground
Notes: - AVSS and HVSS of the AK4645 should be distributed separately from the ground of external controllers. - All digital input pins should not be left floating. - When AIN3 bit = "1", PLL is not available. - When the AK4645 is used at master mode, LRCK and BICK pins are floating before M/S bit is changed to "1". Therefore, 100k around pull-up resistor should be connected to LRCK and BICK pins of the AK4645. - 0.1F ceramic capacitor should be attached to each supply pins. The type of other capacitors is not critical. - When DVDD is supplied from AVDD via 10 series resistor, the capacitor larger than 0.1F should not be connected between DVDD and the ground. Figure 74. Typical Connection Diagram (AIN3 bit = "1": PLL is not available, Line Input)
MS0605-E-00 - 83 -
2007/06
[AK4645EZ]
1. Grounding and Power Supply Decoupling
The AK4645 requires careful attention to power supply and grounding arrangements. AVDD, DVDD, TVDD and HVDD are usually supplied from the system's analog supply. If AVDD, DVDD, TVDD and HVDD are supplied separately, the power-up sequence is not critical. PDN pin should be held to "L" upon power-up. PDN pin should be set to "H" after all power supplies are powered-up. In case that the pop noise should be avoided at line output and headphone output, the AK4645 should be operated by the following recommended power-up/down sequence. 1) Power-up - PDN pin should be held to "L" upon power-up. The AK4645 should be reset by bringing PDN pin "L" for 150ns or more. - In case that the power supplies are separated in two or more groups, the power supply including TVDD should be powered ON at first. Regarding the relationship between DVDD and HVDD, the power supply including DVDD should be powered ON prior to the power supply including HVDD. 2) Power-down - Each power supplies should be powered OFF after PDN pin is set to "L". - In case that the power supplies are separated in two or more groups, the power supply including TVDD should be powered OFF at last. Regarding the relationship between DVDD and HVDD, the power supply including HVDD should be powered OFF prior to the power supply including DVDD. AVSS and HVSS of the AK4645 should be connected to the analog ground plane. System analog ground and digital ground should be connected together near to where the supplies are brought onto the printed circuit board. Decoupling capacitors should be as near to the AK4645 as possible, with the small value ceramic capacitor being the nearest.
2. Voltage Reference
VCOM is a signal ground of this chip. A 2.2F electrolytic capacitor in parallel with a 0.1F ceramic capacitor attached to the VCOM pin eliminates the effects of high frequency noise. No load current may be drawn from the VCOM pin. All signals, especially clocks, should be kept away from the VCOM pin in order to avoid unwanted coupling into the AK4645.
3. Analog Inputs
The Mic, Line and MIN inputs are single-ended. The input signal range scales with nominally at 0.06 x AVDD Vpp(typ) @MGAIN1-0 bits = "01", 0.03 x AVDD Vpp(typ) @MGAIN1-0 bits = "10", 0.015 x AVDD Vpp(typ) @MGAIN1-0 bits = "11" or 0.6 x AVDD Vpp(typ) @MGAIN1-0 bits = "00" for the Mic/Line input and 0.6 x AVDD Vpp (typ) for the MIN input, centered around the internal common voltage (0.45 x AVDD). Usually the input signal is AC coupled using a capacitor. The cut-off frequency is fc = (1/2RC). The AK4645 can accept input voltages from AVSS to AVDD.
4. Analog Outputs
The input data format for the DAC is 2's complement. The output voltage is a positive full scale for 7FFFH(@16bit) and a negative full scale for 8000H(@16bit). The ideal output is VCOM voltage for 0000H(@16bit). Stereo Line Output is centered at 0.45 x AVDD. The Headphone-Amp output is centered at HVDD/2.
MS0605-E-00 - 84 -
2007/06
[AK4645EZ]
CONTROL SEQUENCE
Clock Set up
When ADC or DAC is powered-up, the clocks must be supplied. 1. PLL Master Mode.
Example:
Power Supply
(1)
PDN pin
(2) (3)
Audio I/F Format: MSB justified (ADC & DAC) BICK frequency at Master Mode: 64fs Input Master Clock Select at PLL Mode: 11.2896MHz MCKO: Enable Sampling Frequency: 44.1kHz
PMVCM bit
(Addr:00H, D6) (4)
MCKO bit
(Addr:01H, D1)
(1) Power Supply & PDN pin = "L"
"H"
PMPLL bit
(Addr:01H, D0) (5)
MCKI pin
Input
(2)Addr:01H, Data:08H Addr:04H, Data:4AH Addr:05H, Data:27H
M/S bit
(Addr:01H, D3) 40msec(max) (6)
(3)Addr:00H, Data:40H
Output
40msec(max) (8)
BICK pin LRCK pin
(4)Addr:01H, Data:0BH
MCKO pin
(7)
Output
MCKO, BICK and LRCK output
Figure 75. Clock Set Up Sequence (1)
(1) After Power Up, PDN pin = "L" "H". "L" time of 150ns or more is needed to reset the AK4645. The AK4645 should be operated by the recommended power-up/down sequence shown in "System Design (Grounding and Power Supply Decoupling)" to avoid the pop noise at line output and headphone output. (2) DIF1-0, PLL3-0, FS3-0, BCKO and M/S bits should be set during this period. (3) Power UpVCOM: PMVCM bit = "0" "1" VCOM should first be powered-up before the other block operates. (4) In case of using MCKO output: MCKO bit = "1" In case of not using MCKO output: MCKO bit = "0" (5) PLL lock time is 40ms(max) after PMPLL bit changes from "0" to "1" and MCKI is supplied from an external source. (6) The AK4645 starts to output the LRCK and BICK clocks after the PLL becomes stable. Then normal operation starts. (7) The invalid frequency is output from MCKO pin during this period if MCKO bit = "1". (8) The normal clock is output from MCKO pin after the PLL is locked if MCKO bit = "1".
MS0605-E-00 - 85 -
2007/06
[AK4645EZ]
2. PLL Slave Mode (LRCK or BICK pin)
Example:
Power Supply
(1)
PDN pin
(2) (3)
Audio I/F Format: MSB justified (ADC & DAC) PLL Reference clock: BICK BICK frequency: 64fs Sampling Frequency: 44.1kHz
PMVCM bit
(Addr:00H, D6)
4fs ofPower Supply & PDN pin = "L" (1)
"H"
PMPLL bit
(Addr:01H, D0)
(2) Addr:04H, Data:32H Addr:05H, Data:27H
Input
(4)
LRCK pin BICK pin Internal Clock
(3) Addr:00H, Data:40H
(5)
(4) Addr:01H, Data:01H
Figure 76. Clock Set Up Sequence (2)
(1) After Power Up, PDN pin = "L" "H". "L" time of 150ns or more is needed to reset the AK4645. The AK4645 should be operated by the recommended power-up/down sequence shown in "System Design (Grounding and Power Supply Decoupling)" to avoid the pop noise at line output and headphone output. (2) DIF1-0, FS3-0 and PLL3-0 bits should be set during this period. (3) Power Up VCOM: PMVCM bit = "0" "1" VCOM should first be powered up before the other block operates. (4) PLL starts after the PMPLL bit changes from "0" to "1" and PLL reference clock (LRCK or BICK pin) is supplied. PLL lock time is 160ms(max) when LRCK is a PLL reference clock. And PLL lock time is 2ms(max) when BICK is a PLL reference clock. (5) Normal operation stats after that the PLL is locked.
MS0605-E-00 - 86 -
2007/06
[AK4645EZ]
3. PLL Slave Mode (MCKI pin)
Example:
Audio I/F Format: MSB justified (ADC & DAC) BICK frequency at Master Mode: 64fs Input Master Clock Select at PLL Mode: 11.2896MHz MCKO: Enable Sampling Frequency: 44.1kHz
Power Supply
(1)
(1) Power Supply & PDN pin = "L"
(2) (3)
"H"
PDN pin PMVCM bit
(Addr:00H, D6) (4)
(2)Addr:04H, Data:4AH Addr:05H, Data:27H
MCKO bit
(Addr:01H, D1)
(3)Addr:00H, Data:40H
PMPLL bit
(Addr:01H, D0) (5)
MCKI pin
Input
40msec(max) (7)
(4)Addr:01H, Data:03H
MCKO output start
Output
MCKO pin
(6) (8)
BICK pin LRCK pin
Input
BICK and LRCK input start
Figure 77. Clock Set Up Sequence (3)
(1) After Power Up, PDN pin = "L" "H". "L" time of 150ns or more is needed to reset the AK4645. The AK4645 should be operated by the recommended power-up/down sequence shown in "System Design (Grounding and Power Supply Decoupling)" to avoid the pop noise at line output and headphone output. (2) DIF1-0, PLL3-0 and FS3-0 bits should be set during this period. (3) Power Up VCOM: PMVCM bit = "0" "1" VCOM should first be powered up before the other block operates. (4) Enable MCKO output: MCKO bit = "1" (5) PLL starts after that the PMPLL bit changes from "0" to "1" and PLL reference clock (MCKI pin) is supplied. PLL lock time is 40ms(max). (6) The invalid frequency is output from MCKO during this period. (7) The normal clock is output from MCKO after PLL is locked. (8) BICK and LRCK clocks should be synchronized with MCKO clock.
MS0605-E-00 - 87 -
2007/06
[AK4645EZ]
4. EXT Slave Mode
Example:
Audio I/F Format: MSB justified (ADC and DAC) Input MCKI frequency: 256fs Sampling Frequency: 44.1kHz MCKO: Disable
Power Supply
(1)
(1) Power Supply & PDN pin = "L"
"H"
PDN pin
(2) (3)
PMVCM bit
(Addr:00H, D6) (4)
(2) Addr:04H, Data:02H Addr:05H, Data:00H
Input
(4)
MCKI pin LRCK pin BICK pin
(3) Addr:00H, Data:40H
Input
MCKI, BICK and LRCK input
Figure 78. Clock Set Up Sequence (4)
(1) After Power Up, PDN pin = "L" "H". "L" time of 150ns or more is needed to reset the AK4645. The AK4645 should be operated by the recommended power-up/down sequence shown in "System Design (Grounding and Power Supply Decoupling)" to avoid the pop noise at line output and headphone output. (2) DIF1-0 and FS1-0 bits should be set during this period. (3) Power Up VCOM: PMVCM bit = "0" "1" VCOM should first be powered up before the other block operates. (4) Normal operation starts after the MCKI, LRCK and BICK are supplied.
MS0605-E-00 - 88 -
2007/06
[AK4645EZ]
5. EXT Master Mode
Example:
Audio I/F Format: MSB justified (ADC and DAC) Input MCKI frequency: 256fs Sampling Frequency: 44.1kHz MCKO: Disable
Power Supply
(1)
(1) Power Supply & PDN pin = "L"
"H"
PDN pin
(4)
(2) MCKI input (3) Addr:04H, Data:02H Addr:05H, Data:00H Addr:01H, Data:08H
PMVCM bit
(Addr:00H, D6) (2)
MCKI pin
(3)
Input
M/S bit
(Addr:01H, D3)
BICK and LRCK output
Output
LRCK pin BICK pin
(4) Addr:00H, Data:40H
Figure 79. Clock Set Up Sequence (5)
(1) After Power Up, PDN pin = "L" "H". "L" time of 150ns or more is needed to reset the AK4645. The AK4645 should be operated by the recommended power-up/down sequence shown in "System Design (Grounding and Power Supply Decoupling)" to avoid the pop noise at line output and headphone output. (2) MCKI should be input. (3) After DIF1-0 and FS1-0 bits are set, M/S bit should be set to "1". Then LRCK and BICK are output. (4) Power Up VCOM: PMVCM bit = "0" "1" VCOM should first be powered up before the other block operates.
MS0605-E-00 - 89 -
2007/06
[AK4645EZ]
MIC Input Recording (Stereo)
Example:
PLL Master Mode Audio I/F Format:MSB justified (ADC & DAC) Sampling Frequency:44.1kHz Pre MIC AMP:+20dB MIC Power On ALC setting:Refer to Table 34 ALC bit="1"
FS3-0 bits
(Addr:05H, D5&D2-0)
0,000
(1)
1,111
(1) Addr:05H, Data:27H
MIC Control
(Addr:02H, D2-0)
001
(2)
101 3CH
(3)
(2) Addr:02H, Data:05H
ALC Control 1
(Addr:06H)
00H E1H
(4)
(3) Addr:06H, Data:3CH
ALC Control 2
(Addr:08H)
E1H
(4) Addr:08H, Data:E1H
(5) Addr:0BH, Data:00H
ALC Control 3
(Addr:0BH)
00H
(5)
00H
(6) Addr:07H, Data:21H
ALC Control 4
(Addr:07H)
07H
(6)
21H
(9)
01H ALC Disable
(7) Addr:00H, Data:41H Addr:10H, Data:01H
ALC State PMADL/R bits
(Addr:00H&10H, D0)
ALC Disable
ALC Enable
Recording (8) Addr:00H, Data:40H Addr:10H, Data:00H
1059 / fs (7) (8)
ADC Internal State
Power Down
Initialize Normal State Power Down
(9) Addr:07H, Data:01H
Figure 80. MIC Input Recording Sequence This sequence is an example of ALC setting at fs=44.1kHz. If the parameter of the ALC is changed, please refer to "Figure 36. Registers set-up sequence at ALC operation" At first, clocks should be supplied according to "Clock Set Up" sequence. (1) Set up a sampling frequency (FS3-0 bit). When the AK4645 is PLL mode, MIC and ADC should be powered-up in consideration of PLL lock time after a sampling frequency is changed. (2) Set up MIC input (Addr: 02H) (3) Set up Timer Select for ALC (Addr: 06H) (4) Set up REF value for ALC (Addr: 08H) (5) Set up LMTH1 and RGAIN1 bits (Addr: 0BH) (6) Set up LMTH0, RGAIN0, LMAT1-0 and ALC bits (Addr: 07H) (7) Power Up MIC and ADC: PMADL = PMADR bits = "0" "1" The initialization cycle time of ADC is 1059/fs=24ms@fs=44.1kHz. After the ALC bit is set to "1" and MIC&ADC block is powered-up, the ALC operation starts from IVOL default value (+30dB). The time of offset voltage going to "0" after the ADC initialization cycle depends on both the time of analog input pin going to the common voltage and the time constant of the offset cancel digital HPF. This time can be shorter by using the following sequence: At first, PMVCM and PMMP bits should set to "1". Then, the ADC should be powered-up. The wait time to power-up the ADC should be longer than 4 times of the time constant that is determined by the AC coupling capacitor at analog input pin and the internal input resistance 60k(typ). (8) Power Down MIC and ADC: PMADL = PMADR bits = "1" "0" When the registers for the ALC operation are not changed, ALC bit may be keeping "1". The ALC operation is disabled because the MIC&ADC block is powered-down. If the registers for the ALC operation are also changed when the sampling frequency is changed, it should be done after the AK4645 goes to the manual mode (ALC bit = "0") or MIC&ADC block is powered-down (PMADL=PMADR bits = "0"). IVOL gain is not reset when PMADL=PMADR bits = "0", and then IVOL operation starts from the setting value when PMADL or PMADR bit is changed to "1". (9) ALC Disable: ALC bit = "1" "0" MS0605-E-00 - 90 2007/06
[AK4645EZ]
Headphone-amp Output
E x a m p le :
P L L M a s te r M o d e S a m p lin g F r e q u e n c y : 4 4 . 1 k H z D V O L C b it = " 1 " ( d e fa u lt ) D ig it a l V o lu m e L e v e l: - 8 d B B a s s B o o s t L e v e l: M id d le D e -e m p h a s e s re s p o n s e : O F F S o f t M u t e T im e : 2 5 6 /f s
FS3-0 bits
(Addr:05H, D5&D2-0)
0,000
(1) (2)
1,111
(13)
DACH bit
(Addr:0FH, D0)
( 1 ) A d d r : 0 5 H , D a ta : 2 7 H
( 2 ) A d d r : 0 F H , D a ta 0 9 H
BST1-0 bits
(Addr:0EH, D3-2)
00
(3)
10
(12)
00 91H
(3 ) A d d r:0 E H , D a ta 1 9 H
IVL/R7-0 bits
(Addr:09H&0CH, D7-0)
E1H
(4)
(4 ) A d d r:0 9 H & 0 C H , D a ta 9 1 H
( 5 ) A d d r : 0 A H & 0 D H , D a ta 2 8 H
DVL/R7-0 bits
(Addr:0AH&0DH, D7-0)
18H
(5)
28H
( 6 ) A d d r : 0 0 H , D a ta 6 4 H
PMDAC bit
(Addr:00H, D2) (6) (11)
( 7 ) A d d r : 0 1 H , D a ta 3 9 H
( 8 ) A d d r : 0 1 H , D a ta 7 9 H
PMMIN bit
(Addr:00H, D5)
P la y b a c k
( 9 ) A d d r : 0 1 H , D a ta 3 9 H
PMHPL/R bits
(Addr:01H, D5-4)
(7)
(10)
( 1 0 ) A d d r :0 1 H , D a t a 0 9 H
HPMTN bit
(Addr:01H, D6)
(8)
(9)
( 1 1 ) A d d r :0 0 H , D a t a 4 0 H
( 1 2 ) A d d r :0 E H , D a t a 0 0 H
HPL/R pins
Normal Output
( 1 3 ) A d d r :0 F H , D a t a 0 8 H
Figure 81. Headphone-Amp Output Sequence At first, clocks should be supplied according to "Clock Set Up" sequence. (1) Set up a sampling frequency (FS3-0 bits). When the AK4645 is PLL mode, DAC and Headphone-Amp should be powered-up in consideration of PLL lock time after a sampling frequency is changed. (2) Set up the path of "DAC HP-Amp": DACH bit = "0" "1" (3) Set up the low frequency boost level (BST1-0 bits) (4) Set up the input digital volume (Addr: 09H and 0CH) When PMADL = PMADR bits = "0", IVL7-0 and IVR7-0 bits should be set to "91H"(0dB). (5) Set up the output digital volume (Addr: 0AH and 0DH) When DVOLC bit is "1" (default), DVL7-0 bits set the volume of both channels. After DAC is powered-up, the digital volume changes from default value (0dB) to the register setting value by the soft transition. (6) Power up DAC and MIN-Amp: PMDAC = PMMIN bits = "0" "1" The DAC enters an initialization cycle that starts when the PMDAC bit is changed from "0" to "1" at PMADL and PMADR bits are "0". The initialization cycle time is 1059/fs=24ms@fs=44.1kHz. During the initialization cycle, the DAC input digital data of both channels are internally forced to a 2's compliment, "0". The DAC output reflects the digital input data after the initialization cycle is complete. When PMADL or PMADR bit is "1", the DAC does not require an initialization cycle. When ALC bit is "1", ALC is disable (ALC gain is set by IVL/R7-0 bits) during an intialization cycle (1059/fs=24ms@fs=44.1kHz). After the initialization cycle, ALC operation starts from the gain set by IVL/R7-0 bits. (7) Power up headphone-amp: PMHPL = PMHPR bits = "0" "1" Output voltage of headphone-amp is still HVSS. (8) Rise up the common voltage of headphone-amp: HPMTN bit = "0" "1" The rise time depends on HVDD and the capacitor value connected with the MUTET pin. When HVDD=3.3V and the capacitor value is 1.0F, the time constant is r = 100ms(typ), 250ms(max). (9) Fall down the common voltage of headphone-amp: HPMTN bit = "1" "0" The fall time depends on HVDD and the capacitor value connected with the MUTET pin. When HVDD=3.3V and the capacitor value is 1.0F, the time constant is f = 100ms(typ), 250ms(max). If the power supply is powered-off or headphone-Amp is powered-down before the common voltage goes to GND, the pop noise occurs. It takes twice of f that the common voltage goes to GND. (10) Power down headphone-amp: PMHPL = PMHPR bits = "1" "0" (11) Power down DAC and MIN-Amp: PMDAC = PMMIN bits = "1" "0" (12) Off the bass boost: BST1-0 bits = "00" (13) Disable the path of "DAC HP-Amp": DACH bit = "1" "0"
MS0605-E-00 - 91 -
2007/06
[AK4645EZ]
Stereo Line Output
Example:
PLL, Master Mode Audio I/F Format :MSB justified (ADC & DAC) Sampling Frequency: 44.1kHz Digital Volume: -8dB LOVL=MINL bits = "0"
FS3-0 bits
(Addr:05H, D5&D2-0)
0,000
(1)
1,111
(10)
(1) Addr:05H, Data:27H (2) Addr:02H, Data:10H
DACL bit
(Addr:02H, D4)
(2)
IVL/R7-0 bits
(Addr:09H&0CH, D7-0)
E1H
(3)
91H
(3) Addr:09H&0CH, Data:91H (4) Addr:0AH&0DH, Data:28H
DVL/R7-0 bits
(Addr:0AH&0DH, D7-0)
18H
(4)
28H
(5) Addr:03H, Data:40H (6) Addr:00H, Data:6CH
LOPS bit
(Addr:03H, D6) (5) (7) (8) (11)
PMDAC bit
(Addr:00H, D2)
(7) Addr:03H, Data:00H Playback (8) Addr:03H, Data:40H
PMMIN bit
(Addr:00H, D5) (6) (9)
PMLO bit
(Addr:00H, D3) >300 ms
(9) Addr:00H, Data:40H (10) Addr:02H, Data:00H
LOUT pin ROUT pin
>300 ms
Normal Output
(11) Addr:03H, Data:00H
Figure 82. Stereo Lineout Sequence At first, clocks should be supplied according to "Clock Set Up" sequence. (1) Set up the sampling frequency (FS3-0 bits). When the AK4645 is PLL mode, DAC and Stereo Line-Amp should be powered-up in consideration of PLL lock time after the sampling frequency is changed. (2) Set up the path of "DAC Stereo Line Amp": DACL bit = "0" "1" (3) Set up the input digital volume (Addr: 09H and 0CH) When PMADL = PMADR bits = "0", IVL7-0 and IVR7-0 bits should be set to "91H"(0dB). (4) Set up the output digital volume (Addr: 0AH and 0DH) When DVOLC bit is "1" (default), DVL7-0 bits set the volume of both channels. After DAC is powered-up, the digital volume changes from default value (0dB) to the register setting value by the soft transition. (5) Enter power-save mode of Stereo Line Amp: LOPS bit = "0" "1" (6) Power-up DAC, MIN-Amp and Stereo Line-Amp: PMDAC = PMMIN = PMLO bits = "0" "1" The DAC enters an initialization cycle that starts when the PMDAC bit is changed from "0" to "1" at PMADL and PMADR bits are "0". The initialization cycle time is 1059/fs=24ms@fs=44.1kHz. During the initialization cycle, the DAC input digital data of both channels are internally forced to a 2's compliment, "0". The DAC output reflects the digital input data after the initialization cycle is complete. When PMADL or PMADR bit is "1", the DAC does not require an initialization cycle. When ALC bit is "1", ALC is disable (ALC gain is set by IVL/R7-0 bits) during an intialization cycle (1059/fs=24ms@fs=44.1kHz). After the initialization cycle, ALC operation starts from the gain set by IVL/R7-0 bits. LOUT and ROUT pins rise up to VCOM voltage after PMLO bit is changed to "1". Rise time is 300ms(max) at C=1F and AVDD=3.3V. (7) Exit power-save mode of Stereo Line-Amp: LOPS bit = "1" "0" LOPS bit should be set to "0" after LOUT and ROUT pins rise up. Stereo Line-Amp goes to normal operation by setting LOPS bit to "0". (8) Enter power-save mode of Stereo Line-Amp: LOPS bit: "0" "1" (9) Power-down DAC, MIN-Amp and Stereo Line-Amp: PMDAC = PMMIN = PMLO bits = "1" "0" LOUT and ROUT pins fall down to AVSS. Fall time is 300ms(max) at C=1F and AVDD=3.3V. (10) Disable the path of "DAC Stereo Line-Amp": DACL bit = "1" "0" (11) Exit power-save mode of Stereo Line-Amp: LOPS bit = "1" "0" LOPS bit should be set to "0" after LOUT and ROUT pins fall down.
MS0605-E-00 - 92 -
2007/06
[AK4645EZ]
Stop of Clock
Master clock can be stopped when ADC and DAC are not used. 1. PLL Master Mode
Example:
(1)
PMPLL bit
(Addr:01H, D0) (2)
Audio I/F Format: MSB justified (ADC & DAC) BICK frequency at Master Mode: 64fs Input Master Clock Select at PLL Mode: 11.2896MHz Sampling Frequency: 44.1kHz
MCKO bit
(Addr:01H, D1)
"1" or "0" (3)
(1) (2) Addr:01H, Data:08H (3) Stop an external MCKI
External MCKI
Input
Figure 83. Clock Stopping Sequence (1) (1) Power down PLL: PMPLL bit = "1" "0" (2) Stop MCKO clock: MCKO bit = "1" "0" (3) Stop an external master clock. 2. PLL Slave Mode (LRCK or BICK pin)
Example
(1)
PMPLL bit
(Addr:01H, D0) (2)
Audio I/F Format: MSB justified (ADC & DAC) PLL Reference clock: BICK BICK frequency: 64fs Sampling Frequency: 44.1kHz
External BICK External LRCK
Input
(2)
(1) Addr:01H, Data:00H
Input
(2) Stop the external clocks
Figure 84. Clock Stopping Sequence (2) (1) Power down PLL: PMPLL bit = "1" "0" (2) Stop the external BICK and LRCK clocks 3. PLL Slave (MCKI pin)
(1)
Example
Audio I/F Format: MSB justified (ADC & DAC) PLL Reference clock: MCKI BICK frequency: 64fs Sampling Frequency: 44.1kHz
PMPLL bit
(Addr:01H, D0) (1)
MCKO bit
(Addr:01H, D1) (2)
(1) Addr:01H, Data:00H
External MCKI
Input
(2) Stop the external clocks
Figure 85. Clock Stopping Sequence (3) (1) Power down PLL: PMPLL bit = "1" "0" Stop MCKO output: MCKO bit = "1" "0" (2) Stop the external master clock.
MS0605-E-00 - 93 -
2007/06
[AK4645EZ]
4. EXT Slave Mode
(1)
External MCKI External BICK External LRCK
Input
Example
(1)
Input
(1)
Audio I/F Format: MSB justified (ADC & DAC) Input MCKI frequency: 1024fs Sampling Frequency: 44.1kHz
Input
(1) Stop the external clocks
Figure 86. Clock Stopping Sequence (4)
(1) Stop the external MCKI, BICK and LRCK clocks.
5. EXT Master Mode
(1)
External MCKI BICK LRCK
Input
Example
Output Output
"H" or "L" "H" or "L"
Audio I/F Format: MSB justified (ADC & DAC) Input MCKI frequency: 1024fs Sampling Frequency: 44.1kHz
(1) Stop the external MCKI
Figure 87. Clock Stopping Sequence (5)
(1) Stop MCKI clock. BICK and LRCK are fixed to "H" or "L".
Power down
Power supply current can be shut down (typ. 20A) by stopping clocks and setting PMVCM bit = "0" after all blocks except for VCOM are powered-down. Power supply current can be also shut down (typ. 1A) by stopping clocks and setting PDN pin = "L". When PDN pin = "L", the registers are initialized.
MS0605-E-00 - 94 -
2007/06
[AK4645EZ]
PACKAGE
32pin QFN (Unit: mm)
4.0 0.1
17 16
2.6 0.1
24
0.40 0.10
25
4.0 0.1
A
2.6 0.1
Exposed Pad
9 8
B
32
0.45 0.10
1
0.22 0.05
0.18 0.05
0.05 M
C0.3 PIN #1 ID
0.08
0.4
Note) The exposed pad on the bottom surface of the package must be open or connected to the ground.
Material & Lead finish
Package molding compound: Lead frame material: Lead frame surface treatment: Epoxy Cu Solder (Pb free) plate
MS0605-E-00 - 95 -
0.00 MIN 0.05 MAX
0.65 MAX
2007/06
[AK4645EZ]
MARKING
4645
XXXX
1
XXXX: Date code (4 digit) Pin #1 indication
REVISION HISTORY
Date (YY/MM/DD) 07/06/19 Revision 00 Reason First Edition Page Contents
IMPORTANT NOTICE These products and their specifications are subject to change without notice. When you consider any use or application of these products, please make inquiries the sales office of Asahi Kasei EMD Corporation (AKEMD) or authorized distributors as to current status of the products. AKEMD assumes no liability for infringement of any patent, intellectual property, or other rights in the application or use of any information contained herein. Any export of these products, or devices or systems containing them, may require an export license or other official approval under the law and regulations of the country of export pertaining to customs and tariffs, currency exchange, or strategic materials. AKEMD products are neither intended nor authorized for use as critical componentsNote1) in any safety, life support, or other hazard related device or systemNote2), and AKEMD assumes no responsibility for such use, except for the use approved with the express written consent by Representative Director of AKEMD. As used here: Note1) A critical component is one whose failure to function or perform may reasonably be expected to result, whether directly or indirectly, in the loss of the safety or effectiveness of the device or system containing it, and which must therefore meet very high standards of performance and reliability. Note2) A hazard related device or system is one designed or intended for life support or maintenance of safety or for applications in medicine, aerospace, nuclear energy, or other fields, in which its failure to function or perform may reasonably be expected to result in loss of life or in significant injury or damage to person or property. It is the responsibility of the buyer or distributor of AKEMD products, who distributes, disposes of, or otherwise places the product with a third party, to notify such third party in advance of the above content and conditions, and the buyer or distributor agrees to assume any and all responsibility and liability for and hold AKEMD harmless from any and all claims arising from the use of said product in the absence of such notification.
MS0605-E-00 - 96 -
2007/06

▲Up To Search▲

Price & Availability of AK4645EZ

	To Download AK4645EZ Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .